creality support 3d models
742232 3d models found related to creality support.
thingiverse
EDIT 22/02/23: I have included a modified version of the grille to include supports for an endoscope mount like this: https://www.thingiverse.com/thing:4742800 This is a remix from tllado's Quiet Cooler for Creality Ender 3 v2...
thingiverse
Drive the extruder: This supports a nut that holds a filament tube, which you'll need for assembly. Required parts: 1. An old extruder spring 2. A small M3 or M4 bolt 3. A 608zz round bearing That's all for parts. ... This upgrade provides no-slip...
thingiverse
This is a mount for a Nema 17 stepper motor that fits any printer with a 2020 extrusion. It secures to the top, next to the spool, using two bolts and square/t-nuts. An extended cable is necessary. This setup enhances filament flow on machines like...
thingiverse
I made this supported the LED bar in the Ender3Plus structure.The support is made to fit the 20x20 aluminum profile top, is very well fixed without any sensation of oscillation, and is not loose.It is a simple, fast and economic solution.The wiring...
thingiverse
Notably, no support material is required for printing any of these parts. Two distinct camera cases have been created, differing only in the orientation of the cable exit on each side. Both cases utilize the same CameraBack component. As depicted...
thingiverse
Printing with PLA on CR-10: Dimensions: Outer diameter = 22mm Inner diameter = 8mm Thickness = 7mm Screw size: M8 Bolt specifications: M8 x 0.8 thread pitch, length of threading = 40 mm
prusaprinters
Print with PLA in CR-10 Dimensions roulement : diametre exterieure = 22 mm diametre intérieur = 8 mm epaisseur = 7 mm Ecrou de 8 Boulon : 8.8 CM / longueur filetage : 40 mm Category: 3D Printer Accessories
thingiverse
There is no need for support or rafts because the lugs are cut away underneath to print without them. The model prints at 3shell with 1% infill and gap filling at 0.2mm. It takes about 40 minutes to print using around 2 meters of filament. If you're...
thingiverse
Mounting the filament guide requires a clear path on the Z-axis. ...Simply attach it with the spare parts provided with your 3D printer.
thingiverse
Modified Mediaman's V6 Mount for Personal Use I recently revised the popular V6 mount by Mediaman on Thingiverse, with a focus on meeting my specific requirements. ...The updated design is now available for anyone to use and benefit from.
thingiverse
You're free to repurpose the leftover components from the printer as needed.
cults3d
I wanted a SD-Card Holder for normal sized SDs for my new CR-6 SE. This is an easy print, just make sure bed adhesion is good so that the part not warps. It can be installed with the two stock screws that keep front cover attached to the left 40x40...
thingiverse
I wanted a SD-Card Holder for normal sized SDs for my new CR-6 SE. This is an easy print, just make sure bed adhesion is good so that the part not warps. It can be installed with the two stock screws that keep front cover attached to the left 40x40...
cults3d
Creality support for Sanelec 1240 30cm lamp or similar, for Creality CR-10 V3, and v2 printer support structure (or any other that had that type of supports).
thingiverse
These are my upgrades for the Creality CR-10 S5 500mm printer. The frame braces and spool holder utilize M8 threaded rods and M8 nuts. The spool holder relies on two 608 ball bearings The rods must be at least 72 cm long for the two braces and...
cults3d
... mechanisms. simple or original mechanisms do not have the same dimensions, which makes mounting on this support laborious if not impossible. ... for original or single-drive extruders, ready-made STLs are already available and easy to find.
cults3d
... handles of the Creality pliers, printable without supports. ...The 2 pliers are different to put the spring. Here are the parts to replace the handles of the Creality pliers, printable without supports. ...The 2 clamps are different to put the spring.
thingiverse
Creality Ender 3 Pro X MGN12H 300mm Linear Rail No Mods Light Simple Fast single y bearing support Easy to print, suggested PETG No modifications required but just to adjust Y endstop 3mm forward and a proper leveling Fists standard or Micro Swiss...
thingiverse
... take your SD card board out of the black casing and insert it into this. Plus, there's a space for a spare SD card, and the extra cable is easier to fold in with some cable supports to hold it in place; it also has support under the USB cable slot.
thingiverse
My only modification was adding an extra support at the top of the bracket to enhance its rigidity and prevent it from flexing under pressure when tightening the Y-axis belt. This updated version should be printed using the same settings as the...
thingiverse
My modified breakout board cover is here https://www.thingiverse.com/thing:4763930 My 40mm hot-end cooling fan adapter is here https://www.thingiverse.com/thing:4758855 My 40mm fan covers are here https://www.thingiverse.com/thing:4758067 UPDATE:...