creator pro flashforge 3d models
92275 3d models found related to creator pro flashforge.thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/4o93utz0kmJ Support reglable Creator pro Flashforge 2014-18 Diamètre 50 à 80mm Largueur bobine de 35 à 82mm
thingiverse
Flashforge Creator Pro spoolholder . ... Diameter 25mm (29mm end) and length 89mm
thingiverse
A voxelized version of the FlashForge Creator Pro, Modeled in MagicaVoxel.
thingiverse
... was created by ajwammock as a door handle replacement for the Flashforge Creator Pro. Please post any prints so I can see how it works out for you. Print Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .20 Infill: 20%
thingiverse
A simple clip for a 1/8" (about 3mm) glass plate for the FlashForge Creator Pro. I didn't want to deal with wing nuts every time I change out a new glass plate on top of the printing bed so I made some easily removable clips. ...You can use 2 or 4 to...
thingiverse
I remixed this Because i put this thing on my Flashforge Creator PRO and when it got to the sides the wires and hte tubes got hung up a little bit so I just made a longer one :) good design just needed to be longer. ...Thank You :)
prusaprinters
I had a splash of acetone wipe out the FlashForge Creator Pro logo on the front of my machine, so I printed up a replacement. I've also included an inverted version.</p> <p>This one was printed on glass with an ABS slurry. ...In hindsight, I should have...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=40705 Instructions Using the following options: hole_radius = 2.5 icon_rotation = 0 manual_width = 100 manual_length = 100 icon_size = 12 icon = 0 Font = write/orbitron.dxf message_one =...
thingiverse
These are parts that i have made to enhance the use of my FF Creator Pro printer * Replacement spools for the FlashForge Creator Pro, along with a wall mountable holder * If you don't use the factory filament you're going to need these. * If you buy...
pinshape
I had a splash of acetone wipe out the FlashForge Creator Pro logo on the front of my machine, so I printed up a replacement. I've also included an inverted version. This one was printed on glass with an ABS slurry. In hindsight, I should have...
thingiverse
... CAD tool to add your own features. Enjoy! Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: No Resolution: 200 Infill: 100 Notes: Wood filament at 200 degrees C for extruder and 50 degrees C for bed. ... Keep it slow, around 40mm/s
thingiverse
I had a splash of acetone wipe out the FlashForge Creator Pro logo on the front of my machine, so I printed up a replacement. I've also included an inverted version. This one was printed on glass with an ABS slurry. In hindsight, I should have...
cults3d
I had a splash of acetone wipe out the FlashForge Creator Pro logo on the front of my machine, so I printed up a replacement. I've also included an inverted version. This one was printed on glass with an ABS slurry. In hindsight, I should have...
thingiverse
If you feel that the edge of FF creator pro's handle on both side is too sharp. ...This insertion handle is for you.
thingiverse
This is a remake of the classic FlashForge Hood, readapted for 5mm plexi. ...
thingiverse
A simple plug to fill the handles in the flashforge. However this one allows you to insert a common thermometer so you can monitor internal temps while printing high temp ABS, Nylon etc. The thermometer is the dirt cheap kind you find all over ebay...
thingiverse
After I received my FlashForgeCreator PRO printer, I realized that steppers got very hot during print. I designed Snap - On - Holders for the Steppers. I used standard 24V - 40x40mm Fans from local electronic store and connected direct to printers...
thingiverse
Ein einfacher und schneller Erste Schicht Test für den Creator Pro von FlashForge. Linienbreite Testdruck : 0,8 mm Höhe : 1 mm Fläche Testdruck: maximal circa 125mm x 220 mm Düse Standard Durchmesser: 0,4 mm Wie immer sollte die Breite der...
thingiverse
This simple filament spool hanger was designed to fit on a Flashforge Creator Pro (or Flashforge Creator Pro 2). They fit in the slots on the back where the stock hangers go. The stock hangers were not long enough or small enough diameter for some...
prusaprinters
This is a tube holder which improves the uncoiling of the filament on the Creator Pro from Flashforge. PTFE-Tubing with an outer-diameter of 6 mm can be connected easily for a closed filament path. </p><p><strong>Update:</strong> </p><p>The...
thingiverse
A simple clip to hold the door up on a FlashForge Creator X Pro.
thingiverse
a Large spoolholder for a Flashforge Creator Pro
thingiverse
Simple plug to cover the handles on a Flashforge Creator Pro (not the newest version). ... Print Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Infill: 15% Notes: .3mm Layer Height, ABS, Simplify3d
thingiverse
These hooks fit nicely into the handle of your flashforge creator pro, helps reduce clutter around your printer!
thingiverse
... ...I therefore created a new bracket based on similar work for other Flashforge 3D Printers Print Settings Printer: Flashforge Creator Pro (2016) Rafts: No Supports: No Resolution: Low Infill: 15 % Notes: Printed using PLA at 205 degrees Celcius
thingiverse
The new model of the Flasforge Creator Pro uses a snap type that does not fit many of the spools of different companies. ... This model was provided by Tang (who provides support for Flashforge Creator Pro on Amazon).