crius aio 3d models
2354 3d models found related to crius aio.
thingiverse
the KK board I had was mounted diagonally. ...The new multiwii board was not so I made this adapter which works nice
thingiverse
GPS Suport for Tarot Battery Plate for GPS Crius Mini Users. ... making the fixing holes with the drill
thingiverse
Case for the Crius AIOP v2 with mountig clip for a Walkera RX1002. The RX will sit on top of the case mounted with the clip. ...The clip should just snap into the top part of the Case.
thingiverse
Case for Crius SE / LIte and Holes for Turnigy Receiver Instructions I want a Adapter for my old UAVP Frame
thingiverse
Recently finished my prusa i3 and after some calibration this is one of my first test designs. ...A protective plate for my flight controller Crius AIOP v2 running MultiWii firmware on my quadcopter.
cults3d
I designed this case for a Crius GPS NEO-6 module (v3.1) as I couldn't find any published designs that fitted. This case is for a module pcb of approx 40.5 x 40.5 x 1.0 mm. There are corner pillars in the base for attaching the module if not using...
thingiverse
I designed this case for a Crius GPS NEO-6 module (v3.1) as I couldn't find any published designs that fitted. This case is for a module pcb of approx 40.5 x 40.5 x 1.0 mm. There are corner pillars in the base for attaching the module if not using...
thingiverse
I extended the top plate and put the 45mm distance between the screw holes matching the Crius board holes ( you can see the comparison with the original top mount in one of the picture) Two options to secure the board: 1) double-side tape in addition...
thingiverse
Crius Multiwii SE V2.5 housing dimensions 42x42x9 holes M3 Both LEDs have a hole 3mm A3 A6 A7 hole
grabcad
This model was referenced to make its mounting plate. ...Board size is different than the Crius flight controller.
thingiverse
... made to fit on top of the PX4FMU, but could be used onto any flat surface (where the snap-on can pass over the edge). On the image, a 3DR-radio is fit between the PX4FMU and the Crius mount as well, but there are no mounting holes/fixtures for this.
thingiverse
Made this for my Bixler 2. ...Still a work in progress as im waiting for a smaller receiver i ordered and il make a place for that in the pod. Instructions You need a bixler 2, Crius AIOP V2, apm gps, 3dr radio. ... aiop_bixler_pod.stl need supports.
thingiverse
Case for: Update 11/17 - V2 uloaded changes: Remove: GPS antenna hole removed Add: New hole for radio LEDs GPS CRIUS u-Blox CN-06 GPS Receiver V2.0 from RCTIMER http://www.rctimer.com/product_763.html and RCTimer Radio Telemetry Air Module, same size...
thingiverse
this is a case for the CRIUS NEO-6 GPS V3.1 I got from Bangood.http://www.banggood.com/CRIUS-NEO-6-V3_1-GPS-Module-For-APM-Pixhawk-MWC-Flight-Controller-p-941832.html I made this to use on an FPV EEP airplane (specter by ibcrazy) my intent is to use...
thingiverse
Customized version of http://www.thingiverse.com/thing:774334 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=774334 Instructions Using the following options:...
grabcad
CPU AIO Cooler.Roughly based of Corsair Hydro H100x.For more renderings: https://www.behance.net/gallery/119928255/CPU-AIO-Cooler
myminifactory
This the ultimate form of my micro brushed FPVpv quadcopter. ...I have made it accommodate an All In One (AIO) flight control board and it also has a built-in compartment for the battery.
thingiverse
NLR.STL uses the Happy Model Diamond F4 AIO https://www.racedayquads.com/collections/all-stacks-combos-aios/products/happymodel-diamondf4-aio-whoop-flight-controller-f4-fc-5a-1-2s-4in1-esc-25-200mw-vtx-choose-your-rx NLR_BF.STL uses the BetaFPV 1S...
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/6jilpFg7JPr
thingiverse
I have made a Multiwii / crius mount to use instead of the APM mount on the APM 2.5 Bixler Mount here http://www.thingiverse.com/thing:71336 Now tested in my bixler using ArdupirateNG on my multiwii and it flew great. ... I had an apm 2.5 in my bixler...