crystalyte hub motor 3d models
100854 3d models found related to crystalyte hub motor.
grabcad
Bicycle - rear wheel assy - 24" rim, 3" tire, Crystalyte HT hub-motor and 203mm disk brake, custom made spokes at NewsonSportec (best and cheapest place)
grabcad
Crystalyte Hub-motor TC40100 (100km/h) Crown TC Series. The best made ever!...High power & high torque- Design for 48V ~ 72V battery system- Speed from 65km/hr to 100km/hr- Torque up to 131N.m (72V)Rear wheel motor* Two type of dropout version :-...
grabcad
Bicycle - Electric Hub-Motor - Crystalyte HS (high speed) & HT (high torque) Series. ...World best electric bike hub-motor !...
grabcad
An electric hub motor with threaded shaft on one side.The hub itself acts as a ratchet for freewheel.The model was created with Solid Edge.
grabcad
A hub motor named Pablo.I intended to fabricate this motor, but, since the laminations were not off-the-shelf, it would have been very expensive.
cults3d
The gears in the hub motor will eventually break. ...this is a replacement part because these gears are not sold any more.
thingiverse
The gears in the hub motor will eventually break. ...this is a replacement part because these gears are not sold any more.
thingiverse
Used on a FIRST Robotics window motor hub to hold a 1/2" thinwall aluminum tubing. Print 2. ...Top and Bottom.
thingiverse
Connects NXT motor hubs to Tetrix pieces with the help of some bolts and a lego axle Also check out my blog
grabcad
... on their website. ...It's not completely accurate due to a lack of dimensions.The hub motors are mostly used in skateboards.http://www.michobby.com/product/hub-motor-for-electric-skateboards/Future additions will be- a separate shaft- easier to scale
thingiverse
This hub mounts on the littleBits motor with the D-shaped axle. I made this so my students can tape cardboard wheels or shapes to the motor. ...This is used in place of the motor mate which my students found a little harder to manage for some...
thingiverse
Designed this for an etrike project and needed a mount for the 6.5" hoverboard hub motor I was using. This was printed at 80% infill with 2mm sidewall and top/bottom, with petg printed with side down. This might be overkill and you might be able...
grabcad
Nubs to help the wheel slipping issue on Jacob's Hub motors. Just put them on and use some duct tape to hold them in place. ...The slot is there in case someone wants to glue them on with epoxy to give a larger surface area.
thingiverse
... hubmotor with a flattened axle. ...You can adjust the width of the axle matching your hub motor. DXF file is included for laser / water cutting out of stainless steel. ... Available washers are often cheap steel with mediocre surface protection.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: nuts_external_diameter = 6 build_plate_selector = 3 shell_thickness = 1.2 axle_lenght = 12 finger_diameter = 22.2 layer_thickness = 0.2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: nuts_across_flats = 5.5 flange_height = 4 axle_diameter = 2 axle_thickness = 2 nuts_external_diameter = 6 radial_holes_r_vector = 17...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: build_plate_selector = 3 axle_diameter = 6 nuts_external_diameter = 7.7 screw_diameter = 4 build_plate_manual_y = 190 build_plate_manual_x = 190...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: nuts_external_diameter = 7.7 build_plate_selector = 3 axle_lenght = 16 shell_thickness = 1.2 finger_diameter = 22.2 layer_thickness = 0.2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=723983 Instructions Using the following options: hub_diameter = 25 radial_holes_r_vector = 17 flange_holes_number = 5 nut_height = 3.2 build_plate_selector = 3 screw_diameter = 4 flange_height =...