csl elite playseat challenge 3d models

Since I always hit my knee on the wheelbase, I built an elevation plate to prevent this from happening in the future. The plate is currently 2cm thick, but you can adjust its thickness according to your preference. To install the mod, you will also...

V2 - Altered to 20 degrees angle. Modified handlebrake attachment holes to match original screws with the handlebrake from the picture. Added two more securing holes to bracket. Lowered bracked rim height to attach more firmly without needing shims.

SIM racing enthusiasts rejoice! ...Introducing the ultimate telephone holder designed specifically for the Samsung S7 edge and compatible with the popular CSL Elite base.

Phone Holder for Samsung Galaxy S9 that mounts to both Fanatec CSL Elite & Clubsport Wheel bases for use as a dash. 55mm spacing on the M6 Countersunk cap screws. ...

This product is designed specifically for use with a PlaySeat Challenger Handbrake system. One key feature that sets this part apart is its adjustable handbrake angle, allowing you to customize your experience to suit your preferences. ... In terms of...

I'm trying to fix my Fanatec wheel because the paddle shifters are pretty much dead and it's out of warranty. I decided not to try and fix the electronics board since I don't have the right skills, so I designed a simple mount for two microswitches...

Logitech Driving force H shifter Console to mount to Playseat Challenge. ...Ends up being a quite nice starting setup for a driving simulator rig.<br/> Use PETG with 35% Gyroid infill, and 2pcs M4x30 Screws with washers to mount.<br/> 2019.02.20: REV3...

Optionally you can use two more screws for the mounting part to the playseat, but for me four are more than enough and the shaker is not rotatable without excessive use of force. For printing I used 100% infill, since I am no acoustics / audio...

... & clamp. For Playseat Challlenge, use holder & clamp for rear bars, or holder & clamp_22mm for front bars. ... Nuts & Bolts --------- * Basspump III mounting: 3x M5x30 w/ regular nut * Clamp connection to the chair: 4x M6x40 w/ locking nut

The original rods didn't line up well with my base plate position so I tweaked the rods a little by shortening them and adding a twist to make them sit flush in the brackets. This solution was needed for mounting my Moza R9 with the base plate in the...

Designed to attach a 2x4 to the pedal tray for custom pedal mounting. Hose clamp method seemed like the best solution and works with a 100kg load cell brake as tested. ...Note the foam has to be removed for these to fit properly.

null

https://www.thingiverse.com/thing:4462193 I modified the original to fit my needs better and to fit on a smaller print bed 10x10x10cm. It came out way stronger then the original (which i broke some weeks ago while playing). Big thanks to XORI...

This simple brace prevents wheel base vertical wobbling. It has been designed to fit my Thrustmaster TX (similar to T300) base but should work with other ones. The wheel plate wobbles even being screwed on the most far from seat position. Because of...

Just separated the fused model into two parts so it can be used. Couldn't fix the rounded one the same way. ...The mesh appears to be fused.

I've used the Nobsound G2 100 Watt Mono Amplifier to drive two bodyshakers utilizing the pre-out subwoofer channel my receiver offers, so I've built a mount for it as well. Note: The entire frame was constructed from dimensions found in the Amazon...

My quick and dirty attempt to merge both the logitech shifter mount and the cheap Chinese handbrake mount remix into one. Since I have both the shifter and a similar handbrake. Opens and prints fine with Prusa Slic3r. It works for now, but I...

Created this so you do not have to print so many parts. Use the 2 hinges from the original design. ... I'm using this construction for a while now and it works very well and stable.

Print 4 x Mounts Add 4 x M6x20 Hex screw 4 x M6 Locking Nut 8 x 6,4mm washer 8 x Cable Tie 4,8mm

This creation is a result of utilizing Tinkercad's capabilities. ...Make any desired modifications directly within the tool at https://www.tinkercad.com/things/0UHWbtg4By9.

The remix of fr3zno is very decent! The corners of the mount were a bit sharp so I made a small modification by smoothing the corners. ...

This remix extend clamps by 5 cm to 233 cm.I did it because my shifter gets in the way of the backrest.

Not sure if it would work, can't print it for now, if you try it don't hesitate to leave a comment or even better, some pictures !

I've used the Nobsound G2 100 Watt Mono Amplifier to drive 2 bodyshakers using the pre-out subwoofer channel my receiver provides, so I've made a mount for it as well. Note: The whole frame was made from dimensions found in the Amazon listing, so...

This adapter is designed for the VKB Gladiator NXT flight stick to attach to the Mount-It MI-390 TV pole mount. It is far sturdier than any fully 3D printed mount I have tried and with a single thumb screw, the stick can be removed. The adapter is...

I created my own version of the floano design after experiencing issues with slicing theirs. I had several test versions, but they failed to hold up during intense gear changes. This revised model should prove more durable and last longer. I'm still...

i know you want it ! ... it help me a lot have the controller near both for adding input and for the aux

I've tweaked the design, bumping up its height by 10 millimeters. Now, when you fiddle with the height setting on your slicer, the cap itself will expand to match. ...I made these changes using Tinkercad's intuitive tools.

<p>It's great to have such bright LEDs. However I mostly don't do manual shifting, so they are drawing too much attention. So I've designed this Revolution LED Dimming Plate.</p> <p>The amount of dimming is directly related to your choice of...

stl for the brake strut stack bushing thingy no guarantees this will work in polymer, sharing for a friend that is going to CNC it