ctc a10s 3d models
4490 3d models found related to ctc a10s.thingiverse
Spool holder for the CTC Bizer or the Makerbot Replicator
thingiverse
I crafted this component to seal off the gaps created by taking out my CTC buttons.
thingiverse
Printers Support for CTC Printers Requires a Human Interface Feed Tube.
thingiverse
Shell Housing for Breakthrough at CTC Dual for a BEC Socket - Externally Attached Fan
thingiverse
CTC Spring Loaded \r\n\r\nTwo Precision Ball Bearings 8x3x4\r\n\r\n
thingiverse
CTC A13 spool holder for the side, including spool rod from: https://www.thingiverse.com/thing:3646853 CTC A13 Spulen Halter für die Seite, inklusive Spulen Stange von: https://www.thingiverse.com/thing:3646853
thingiverse
Weil das vom Ender 3 beim CTC A13 extrem gewackelt hat, habe ich es etwas angepasst. ... Because the Ender 3 on the CTC A13 wobbled extremely, I adjusted it a bit.
cults3d
Weil das vom Ender 3 beim CTC A13 extrem gewackelt hat, habe ich es etwas angepasst. ... Because the Ender 3 on the CTC A13 wobbled extremely, I adjusted it a bit.
thingiverse
This is a remake of the CTC spool holder that came with the printer Its only one piece, no threads required. ... I have printed using ABS on the CTC replicator clone.
cults3d
CTC A13 spool holder for the side, including spool rod from: https://www.thingiverse.com/thing:3646853 CTC A13 Spulen Halter für die Seite, inklusive Spulen Stange von: https://www.thingiverse.com/thing:3646853
thingiverse
CTC Dual Spool Adapter for Lower Friction on 30 and 34mm Rods, Compatible with all 52mm Filament Spools. ... Printer Settings Printer: CTC Dual Rafts: Not Necessary Supports: Enabled Resolution: 0.2mm Infill: 10% Notes: Two Outer Shells
thingiverse
A Tool for Cutting PTFE Tubes in the CTC Extruder. ... 33mm Length for Original Nozzle or Drilled MK8 Nozzle, or 24mm for MK8 Nozzle. Print Settings Printer: CTC Rafts: No Supports: No Resolution: 0.2 Infill: 20%
thingiverse
This mod converts the thing from Thingiverse (https://www.thingiverse.com/thing:1161013) into a Prusa-style CTC printer.
thingiverse
I trimmed down the edges slightly to ensure it would fit seamlessly onto my Custom Traveling Castle (CTC) build plate.
thingiverse
I designed this for my CTC dual extruder, but it might just as well fit a Wanhao 4s too.
thingiverse
Insert filament holders into the 3 cm holes located at the rear of your CTC 3D printers.
thingiverse
To Enhance Cooling for CTC Printers: Installation Instructions. ...Fitting the Enhanced Cooler Unit with a Supportive Fan Design.
thingiverse
Endstop assembly for the end switch mounted on the rear wall of the CTC to the Z-axis.
thingiverse
... machines. One has a longer cable than the other. This part is suitable for printers with the longer cable. If the cable on your ctc-10s is shorter you could use my other design which can be found here. ...https://www.thingiverse.com/thing:4923655
thingiverse
... CTC Printer On Its Pre-Drilled Holes (43.5mm Center To Center). Print Settings: Printer: CTC Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 50% Notes: Depending On How Good Your Printer Handles Overhang, Support Might Not Be Needed.
thingiverse
Supporting Filament for CTC Prusa I3. ... Two rings featuring a hole allow effortless insertion of filament into the extruder, preventing accidental ejection.
thingiverse
27 printed chain links\nPrint Settings\nPrinter model: CTC\nRafts: disabled\nSupports: not enabled\nResolution: set to 0.2mm\nInfill density: 10%
prusaprinters
CTC Prusa i3 power protection. Just put this top of power. ...Its thight fit, and stays in place by it self.</p> Category: 3D Printer Parts
thingiverse
Modified the Anet A8 Z motor housing to be compatible with the CTC's plywood frame, which features smaller mounting hole diameters and shorter stepper motor screw lengths.
thingiverse
I'm a large CTC Drucker that has two big holes at the back for the filament rolls. ...This is the matching cover to close them up.
thingiverse
I crafted a personalized remix of Makken104's Ender 3 Fan Cover specifically tailored for the CTC A13 3D printer clone, ensuring seamless compatibility and optimal performance.
thingiverse
Easy-to-use CTC Replicator E3D V6 Mount, designed for direct drive performance. ...Print with ABS and utilize the latest revised files.
thingiverse
So I created a vital upgrade 3D printed part that I call CTC A8 Y Axis Belt Clamp for CTC A8. This 3D printed component I designed specifically to address the problem of adjusting the tension on the belt on a 3D printer without disassembling it. I...
thingiverse
... ...I've seen similar holders here on Thingiverse and created my own based on them. M10 Bolt (Bauhaus) M10 Nut Beveled Roof Board Print Settings Printer: CTC Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 40% Notes: PLA
thingiverse
To Work with My CTC i3 Remix (https://www.thingiverse.com/thing:3328782) The Original Design was a Remix of JackWaterfall's e3D Mounting Solution (https://www.thingiverse.com/thing:2023947) I've Simplified the Design, Removing the " !HOT! ..." Text and...