ctc a10s 3d models

To create a stable spool holder for a CTC Prusa i3 printer, you need to print each piece in duplicate. A threaded rod of 8mm with a length of 15/16 inches is all that's required along with four non-slip pads. ...The reel used was the "Filament Reel...

... the two parts is satisfactory, but the surface finish could be improved. Perhaps playing with the filament thickness will yield more accurate results in the future. Print Settings Printer: CTC Dual Rafts: No Supports: No Resolution: 0.2 Infill: 10

Equipment: Sailfish Firmware installed on CTC dual Extruder Printer Materials: Plastic-like substance - Acrylonitrile polymer material used - PLA Density level 30% for Internal structural layers Heating elements Temperature settings: Extruder at 207...

Hardware: 8 M3 screws (I used 8mm long) 8 M3 nuts Print Settings Printer: CTC Bizer Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 15 % Notes: I set the automatic support in Simplify3D to a resolution of 2 mm, and it added the necessary supports...

The latter item doesn't fit the CTC rework, yet it provides bolt holes for adding a spool mount to the top of the printer - https://www.thingiverse.com/thing:1427114. I have not printed the stand yet, so I'm unsure if it needs to be longer due to the...

The problem is that the original CTC pressed steel arm was to flimsy to take the weight. In addition, the M3 threads in the frame had stripped. I have uploaded 2 versions of a printed spool holder arm. V1 is fixed using the original top M3...

Mounting a versatile side window to your CTC Dual is a straightforward process. To begin, cut the necessary parts from 5mm acrylic using a lasercutter or a table saw - both options should yield satisfactory results. For securing the window in place,...

It comes under the CTC Case and cools the complete mainboard, and steppers too. On the last picture you can see a photo... The right side is the holder material thickness 1.5mm. When you create the fan on it, it will stay hard. ... Print settings:...

This is a basic fan duct, easily printable to cool down your prints on a CTC Prusa I3. ... To get started: - 1 forty by forty fan (I've used the one from the card cooling system) - 2 M3 bolts for tightening the part - 4 M3 screws for the fan (optional)...

The CTC Replicator E3D V5 Mounter is a high-performance mounting system designed to house the E3D V5 all-metal hotend. This advanced hotend features a SN04-N NPN Sensor, which provides precise temperature control and monitoring capabilities. ...The...

I decided to create my own PTFE tubes and clips because the MakerBot replicator clone from CTC didn't come with them. These custom-made clips are designed to line up the filament spool's centre with the tube's opening. I used 15mm screws to attach...

I attach this simple bracket to my CTC DIY printer's HDF base plate to boost stability, simplify relocation and enhance Y belt tensioning. I've printed two of them. One I placed near the front idler for the Y axis belt, while the other goes next to...

... ...For printing, set stick thickness to 3, use Font 'write/Letters.dxf', font size of 10, font thickness of 5, and a stick width of 8. The message to be engraved is 'CTC V.A.D. 2015'. ...Flat bottom should be enabled with a hole radius of 3.

... on every plate measuring 5 mm. Printer Settings: Printer: CTC 3D Rafts: Yes Supports: No Resolution: 0.2mm Infill: It makes no difference Notes: Suitable for printing with ABS, a recommended extruder temperature of 240°C, and a heating bed at 90°C.

Specifications: * Material: High-quality metal or plastic * Mounting options: Adjustable for flexible installation * Compatibility: CTC i3 motherboards and compatible cases Warranty Information: * The CTC i3 fan mount is backed by a limited...

Neues Druckbett für den Alu Umbau des CTC 3D Drucker Benötigt wird: Gefräste Aluminium Platte, siehe Zeichnung 2x 12mmx330mm Welle 2x Flaschlager LMEK12LUU - Lange Version 8x M5x40mm Inbusschrauben 8x M4x8mm Inbusschraube 6x M4x20mm Inbusschraube...

I remixed the E3D V6 Hotend Mount - Single Version - with 40mm Fan - CTC / Makerbot Replicator / Flashforge by swestru to attach a 15mm diameter flexi-conduit for thermocouple, fan and heater wires. The design also accommodates other wires like print...

I'm not thrilled with the nut trap slot setup on my CTC Prusa i3 (plywood frame) either. The z motor mounts are built to be a lot more robust, and they bolt directly into the existing frame holes using a through bolt/nut combo - significantly...

I'm updating my CTC z axis tops with a collet modification. The design draws inspiration from Rasta4i's original creation, which I've modified to include the stabilizer rod collet he initially included. After discussing it with him, we decided it...

... the print bed. This support was printed with an infill setting of 30%. Printer Settings: * Printer: CTC Dual * Rafts: Doesn't Matter * Supports: Doesn't Matter * Resolution: 0.2 * Infill: 30% * Notes: Two shells are sufficient, no need for more.

CTC Dual Printer Feet are the perfect solution, ensuring a smooth print every time. Use them to print with confidence, choosing between ABS and PLA, and adjust the wall thickness to three to achieve a strong structure. Opt for 15% infill for added...

Print Settings: CTC 3D Printer is the printer I used. Rafts are not needed, so that's a no. Supports aren't necessary either, so they're off too. The resolution on my print job was set to 0.1mm for maximum detail. Infill percentage was cranked up to...

I was fed up with my CTC making a vibrating noise while switched on. I created a new design and used rubber washers on the bolts to mount it through the 20mm hole next to the pre-drilled screw holes. I had to redesign the throat at the end since I...

... 1. Set the message as "CTC V.A.D. 2016". 2. Choose a stick thickness of 3. 3. Upload the font file 'write/Letters.dxf'. 4. Set the font size to 10. 5. Specify a hole radius of 3. 6. Increase the font thickness to 5. 7. Set the stick width to 8. 8.

I'm a DIY Enthusiast, and I Created This Handy Tool Holder for My CTC 3D Printer. This nifty holder is specifically designed to hold screws, Allen keys, and even razor blades in place. It clips neatly onto the side of my printer's top or bottom,...

I'm planning to use a Fan with 40mm and 24Volts for my CTC, but it's nowhere to be found. To overcome this obstacle, I designed this Fanmount to accommodate a larger 50mm Fan to effectively cool the Stepperdrivers instead. Fortunately, fans that...

The device is engineered to work seamlessly with machines like the CTC, Replicator, and Flashforge. It would be perfectly suited for any printer that features two 8mm rails placed at exactly 70mm centres. The design has been carefully crafted to...

Print Settings Printer: CTC Dual The printer will do all the work. Rafts: No raft is necessary in this case. Don't bother with extra...

I built a custom enclosure for my CTC Anet8 3D printer, which I had constructed specifically for my grandchildren's enjoyment. The print turned out well, but during rapid X-axis movements, the bed would vibrate noticeably. Upon inspection, I found...

... a small cover that utilizes the original opening as a filament guide. I used flathead screws or countersunk them to secure the cover. Sometimes, the original screws from the CTC can get too close to the printhead if you have very high prints.