ctc a10s 3d models

I wanted to print the 120mm Fan upgrade from der0815typ ( https://www.thingiverse.com/thing:1501856 ) but for me it didnt fit as expected so i had to remix it. ... Now you dont need any support, you can easy swap out the old bottom plate.

This is a reinterpretation of https://www.thingiverse.com/thing:1424857.

Safety Blinds for Installation of Fuse Holders For Heating Bed and Extruder Fuses. ... Compatible with fuse holders from Reichelt such as https://www.reichelt.de/sicherungshalter-fuer-5-x-20-mm-250-v-10-a-schwarz-s-313903-p245383.html?&nbc=1 ...

Human: Fiber Feedstock

A Strengthening for the Z-Axis. ...A ball bearing 608 is required.\nThe cable for the end stop must be pulled out a bit from below so that the cable can be routed over the holder.\nThe compensation piece is 0.5mm high, but it can also be scaled higher...

I upgraded my Bizer with a 12V power supply to accommodate bigger and quieter fans. Since there was limited space below for the new fan to draw air in, I decided to elevate the printer using adjustable feet. To achieve an additional 1cm of height...

I have access to advanced tools that I utilize on the job, and designing a custom logo keychain sounded like an exciting side project. ...I'm curious to know if you think it's a good idea.

Improved Fused Deposition Modeling (FDM) performance is achievable without adding unnecessary components. ...Simply swap out existing parts for optimized ones to enhance the overall printing experience.

3D Printer Settings for 8mm Rod Halter: http://www.thingiverse.com/thing:1855144 Print Settings: Printer Brand: Up! ...Printer Model: Up Mini Raft Support: Disabled Support Material: None Resolution: High Infill Percentage: 75%

I drew and printed this piece to check the alignment of the print bed. It can be clipped onto the X axis guides (8mm rods) and a dial with an 8mm shaft inserted. The holder can be manually adjusted to measure the entire surface area of the table. The...

You require four parts, two for each rail. ...They fit neatly into the stock holes of the case.

If I had created this thing and am satisfied with it, I'd like to share it with you and others. I had some heat cartridges here that I wanted to test at some point but never did because unwrapping all those cables without a pressing need...

Comparatore support, used to perfectly adjust the work plan. ...First measure the desired height and then use the comparator to level the surface at multiple points.

To improve Cabletree

I tweaked the design a notch by eliminating the side compartment and pushing the lower tray up against the front panel's edge instead of letting it drop all the way down to the printer's base - it functions beautifully!

A compact container designed specifically for storing your attractsprays

I upgraded the footings to utilize M6 Buffers as a foundation, significantly minimizing printer vibration.

Improved version of a flexible spool holder with M8 threaded rod.

I've increased the mounting hole for the spindle nut a bit because it's a bit too small when using other Z motors with different nuts. ...I also needed thinner brackets for a heating bed, so I uploaded some 22mm ones if anyone needs them.

I modified the X Axis Upgrade Kit from Rics3D (the designer of the X-Axis conversion) so that you don't have to shorten the X-Axes and now the pulley is held by 2 x 625zz bearings!

I created this design to prevent the filament from wrapping around the filament holder on my Creality Tool Changer. Edit it online at https://www.tinkercad.com/things/ie65ZLdjPSh. ...Print Settings are as follows: Printer: Creality Tool Changer, Rafts:...

Mainly to stabilze the cable loom to avoid cable break, secondary to have a good handle for manual moving of the extruder head during bed leveling. This thing was made with Tinkercad. ...Edit it online https://tinkercad.com/things/gjm2uGYblyR

Revise the y-axis fixture, reducing the tolerance level.

A compact keyless lock for tempered glass plate heat beds.

<p>This is a mount for the BigTreeTech TFT24 display, designed to work with the <a href="https://www.thingiverse.com/thing:3865385">BigTreeTech TFT24 display case</a>.</p> <p>It mounts where the old LCD panel would be and covers most of the opening...

This design is crafted with precision using Tinkercad, a powerful online tool for 3D modeling and editing. ...To explore and make adjustments, simply visit https://www.tinkercad.com/things/kypgzILQfCQ to access the editable model in real-time.

I'm going to rewrite this text for you. Legs for STS Bizer, they are quieter. I printed with PLA and inserted self-adhesive legs 3M. ...The SolidWorks source code is included in the package.

The CBiker's custom template for the case of a large bock and a Böhreschablone. This design is intended specifically for mounting on the front of a housing case. ...The dimensions are as follows: 5 inches by 11 inches by 5 inches, with a bearing type of...

Housing for the MKS Touchscreen Monitor V4 Display Unit