ctc a10s 3d models

... Better Print Results. ... Anchor Above with Sunken Screw Head, Anchor Below for Easier Installation with Integrated Screws. Printer Settings Printer: CTC Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 70% Notes: 4 Shells

I've created an enhanced mount for the Z-axis motors on my CTC I3 printer. To secure these mounts, you can link them together with an M8 rod, attaching it firmly to the M10 Y-Axis rods. ...The Motormount STL file is designed to accommodate both left and...

Every owner of a CTC i3 Pro B recognizes the issue with the Y Sensor, which consistently falls short, causing homing to occur beyond the bed's boundaries. ...This solution addresses the problem head-on by placing the sensor directly on the bed,...

This is a Z-Axis NEMA17 motor mount for wood class CTC i3 Pro B. Reducing the whobble effect requires fixing the drive threaded rod in place with ballbearings. Additionally, two standard ballbearings 625ZZ are needed and will be press-fit into this...

MK10 dual extruder PTFE cutting jig Flashforge, CTC I made this, as there are a couple of other tools about on thingiverse that aren't the correct size. I found using the other versions the nozzle would consistently leak. ... This tool has been made by...

This is a compact tool for the dual nozzle Replicator and its clones, such as the CTC Bizer. I didn't want to remove my entire print head from its carriage to level nozzles, unlike some older printers that require it. The nozzles on the CTC are held...

Print Settings Printer: CTC I3 Rafts: No Supports: No Resolution: .2 Infill: 30% Notes: I did not used a brim Place the side with the "Z" down Post-Printing Nuts Add the M3 nuts with the help of a soldering iron. The hex shaped space for the nuts are...

My CTC Dual printer requires precise modifications, and this project was no exception. The original design's y-axle recess was offset slightly differently than mine, so I had to move it to align with my printer's specifications. This involved some...

Here are my print settings: Printer Brand: RepRap Printer: CTC Prusa i3 Pro B Rafts: No Supports: No Resolution: 0.1 Infill: 20 Here's how I designed this project, take a look at it:...

Replacement for the CTC Prusa i3 Y-axis servo mount, this is a replica of the original wooden part I modeled because I needed a new one and they shipped it to me snapped, fortunately they included a spare but I thought why not model it and print it...

... from eBay if needed. Given that I have two CTC printers - Autobot and Decepticon - I decided to create custom backplates for each machine. ...This customization allows me to tailor their functionality and appearance according to my specific needs.

It may also work on the following printers: MakerBot Replicator 1, FF3DP FlashForge Creator, CTC Creator Dual, WanHao Duplicator 4 and Duplicator 4X. Let me know if it's compatible or not. I hope this modification works well on your printer. If it...

ADDED: CTC_Aero_bracket_V2.stl Improved version for easier assembly and disassembly. Cooling duct uses M3 Knurl Insert Nut threads from eBay (https://www.ebay.com.au/itm/122046120352). M3x4x4 Knurl Insert Nut was used. You may need to trim one...

This is a proximity sensor mount designed specifically for the CTC i3 Pro 3D printer. Strategically positioned on the back of the nozzle, it frees up valuable space on the X-axis, allowing for smoother and more efficient printing operations. The...

CTC Prusa I3 Pro B Z Axis Mount from eBay - A Precise and Customizable Solution For those who desire a high degree of accuracy, this mount is an excellent choice. Its components are meticulously crafted to ensure precise alignment, making it...

... as they can get stuck due to being tightened too securely. Print Settings: Printer: CTC 3D Printer Rafts: No Supports: No Resolution: 0.20 Infill: 25% Notes: I printed these parts with ABS, since they will be attached to the heated print bed.

... it's threaded or not, and any other part of that size will work too. Don't pay attention to the picture settings - I didn't have any 8mm bolts available. Print Settings Printer: CTC Prusa i3 Rafts: No Supports: No Resolution: 0.2 mm Infill: 25%

This is a custom 12mm diameter Z-Probe mount for my CTC Bizer, designed to provide precise positioning and stability. To assemble it, you'll need an M3x20mm screw, an M3x18mm screw, and a M3 nut. The revised version, V2, has a slightly smaller...

Yet another Reprap Full Graphic Smart Discount Controller case - this one designed to be mounted on top of my CTC I3 clone printer. Supports are necessary for the case, but only on build plate. Public OnShape document is here:...

Easier Heizbett setup with 3 point adjustment Print Settings Printer: CTC Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 100% Notes: 2 Shells Print in ABS. Instructions 3.5mm hole front center between...

1x M6x6 countersink screws (base) 1x M3x18 countersink screws from the original extruder (lever) 1x M10x6 countersink screws (bearing) 2x M3 washer (bearing) spring (thickness 0.8mm, inner diameter 6mm, outside diameter 8mm, height 18mm) bearing from...

Removing Bohr's templates from the CTC casing without disassembling it every time is a straightforward process. Locate the Y-axis template still installed inside and press it firmly against the screws that hold it in place. Use a needle or pencil to...

For CTC Prusa I3 clone, Anet 8 and similar 3D printers. ...The knob makes use of an M3 screw (I used a 25mm long screw, but it can be longer) There is also a "stopper" part, which must be used together with an M3 nut, to fasten the adjustment screw...

... ...It's designed specifically for CTC/GEETECH I PRO B, with adjustable height allowing BLT touch with V6 and V6 clones. If you find this useful or like it, consider posting a photo of your print or tipping the designer. Happy printing!

This upgrade replaces the original front support on CTC DIY printers, providing additional features for precise alignment. Please note that since different companies manufacture these printers, measurements may vary. For optimal results when printing...

... attach them using epoxy glue. To make this process smoother, I decided to turn the fittings into adapters before gluing them in place. Print Settings: Printer: CTC Rafts: No Supports: Yes Resolution: 0.1-0.2 Infill: 50% Notes: 3 shells were printed

This nozzle ring light was crafted for my CTC DIY i3 PRO printer and also fits seamlessly onto the Anet A8. It's secured via a screw that is already installed on the print head's underside. ...The LEDs used in this design are 12 white, 5mm units, with...

... when the loops are smaller. This design is suitable for a wide range of printers, including Prusa, Anet, Geetech, and CTC models, as well as many other machines with a 5mm wide frame. ... Feel free to modify these files to suit your specific needs.

The Reprap Full Graphic Smart Discount Controller case is designed to be mounted on top of my CTC I3 clone printer. To support this case, only supports are necessary for the build plate. You can access the public OnShape document here:...

http://www.thingiverse.com/apps/customizer/run?thing_id=570406 For using an 8x10 mirror from Dollar Tree as a print bed on CTC Dual. ... Instructions Using the following settings: bedZ = 4.15mm bedY = 150mm bedX = 230mm screwInset = 5mm glassZ = 1.7mm...