ctc cable 3d models
95664 3d models found related to ctc cable.thingiverse
New cable holder with connector for fan. For CTC, Flashforge with metal extruder. See photo. ...The right spare plug is for an extra fan.
thingiverse
... Das neu hinzugefügte Höhendistanz Cable Cain wurde durch construkt Designed. Damit die die höhe auch stimmt wenn es in verbindung mit dem Cable Cain Extruder Holder 5 Test benutz wird. Print Settings Printer: CTC Bizer Resolution: 0.20 Infill: 30%
thingiverse
After several cable breaks occurring on the print head cable loom I decided to try and design a better cable support. This design seems to work and directly replaces the standard CTC one. It has 2 holes for 6mm Teflon tubing which makes a big...
cults3d
This is a replacement cable guide, for the cables to the print head. ...I broke my original, so I made this, and added a hole for a cable tie to keep the cable better in place. ...Thought other might need it.
thingiverse
Designed this because one of the originals broke when I tried to remove the large cable run on the backside to tighten the screw holding it to the printer case. It was basically hollow. I backwards engineered from the one that wasn't broken. ... This...
thingiverse
Just a quick tube guide to try and hold the cable up at the back of the printer (above the block), to stop the wire danging down and getting caught on the Z linear mounts at the top.
thingiverse
This is another cable chain for my CTC printer. It needs no support because it is a two piece design. There are some clip of differend sizes. Each size gives another radius ot the cain. The Clip is stolen from Open Cable Chain by...
thingiverse
And the cable links from: https://www.thingiverse.com/thing:3491926 For X Axis: https://www.thingiverse.com/thing:4314829
cults3d
And the cable links from: https://www.thingiverse.com/thing:3491926 For X Axis: https://www.thingiverse.com/thing:4314829
thingiverse
two chain links to connect the chain <a href="https://www.thingiverse.com/thing:1104664">thing:1104664</a> to the mounts of <a href="https://www.thingiverse.com/thing:3494729">thing:3494729</a>. for the original motor mount i have remixed 2 clips <a...
thingiverse
So I made this cable-duct which still looks kind of professional (I think at least) but could be easily opened and the cables removed. There is need to drill new holes for it, I intentinally did not use the ones already there. The upper one is...
thingiverse
... machines. One has a longer cable than the other. This part is suitable for printers with the longer cable. If the cable on your ctc-10s is shorter you could use my other design which can be found here. ...https://www.thingiverse.com/thing:4923655
thingiverse
Fixation for the cables of the heatbed of a CTC A13 printer. Simply place it at the left rear screw of the heatbed and fix the cables with a cable tie. ... Two versions available, one needs to be printed with support, the other can be printed without.
thingiverse
If you already have 6mm PTFE tubes, use to help cable stay steady. ...Update: v2: thickened walls because it warped over time Print Settings Rafts: No ...
thingiverse
Rear Bracket - Added 5mm to the base to bring it level with the Top Plate as the cable chain not being level bugged me something crazy. The 20x10 Cable chain itself can be purchased from a large selection of places online... ...completely forgotten...
thingiverse
Feed both cables though your copy of ctc_cable_chain_arm and begin assembling your cable chain by feeding the cable through, and snapping the links together one at a time. I assembled the chain first and fed the wires through later. This was a bit of...
thingiverse
Perfekt fitting cable chain holder for a 7x7 cable chain on a CTC i3.
thingiverse
CTC Prusa i3 power cable cover. Easy install. work in progress. But im using this now in my CTC Prusa i3. ...Print Settings Supports: Yes
thingiverse
I made this simple cable holder for my CTC/Geeetech printer to help stop cable from getting in the way of the Y axis carriage. Use two small cable ties to secure it to the carriage pointing out the back and cable tie it the wire to the holder. ...
thingiverse
The parts are designed to work with the great cable chain by ModelStation. I designed it to fit together, but printed all with a scaling factor of 2/3. Then I drilled a 10 mm hole into the wooden table under the heating bed where the top piece fits...
thingiverse
Original design: [AresMars](https://www.thingiverse.com/thing:1932724) (cable chain) and [xxricsxx](https://www.thingiverse.com/thing:3141936) (frame-printer holders/mounts). Its not perfect, but it works. You need to print 20 chain links (more...
prusaprinters
Original design: AresMars (cable chain) and xxricsxx (frame-printer holders/mounts). Its not perfect, but it works. You need to print 20 chain links (more or less, depending where you place your frame holder part). Feel free to print or remix and...
thingiverse
This replaces the fancy zip tie wire holder on your CTC printer. I had a thermocoupler wire break because of the fancy zip tie and fan wires where starting to wear through the insulation too. ... ...
thingiverse
... chain itself can be purchased from a large selection of places online... completely forgotten exactly where I got mine, Either eBay or Amazon knowing me! Amazon = https://tinyurl.com/y7qcy2ta (Cheapest Cable Chain I've found with a quick search)
thingiverse
Fixation for the cables of the heatbed of a CTC A8 printer. This printer is sold with various names, like A6, A8, DIY i3 and others. Check the locations of the heatbed screws and make sure it fits with your printer! There is a left and right...
thingiverse
I upgraded my CTC Bizer MK8 Extruders to a E3D V6 with this thing https://www.thingiverse.com/thing:2348165 and it works like a charm. But i would have a better fixing for the cables und a fan for the Extruder Stepper, because it gets very hot. ...
thingiverse
... for free movement of the motor. Credit to http://www.thingiverse.com/thing:124700 for the MotorEnd concept. Print Settings Printer: CTC Rafts: No Supports: Yes Resolution: 0.2 Infill: 75% for MotorEnd, 40% for FrameEnd and Link How I Designed This
thingiverse
a mounting for the cable chain (thing:2839723) which rests on the frame. since this part has unintentionally stiffened my frame and thus improved the printing precision, (previously the X-Y angles of objects that had 90° in the slicer were not...
thingiverse
***related to this thread*** https://www.thingiverse.com/groups/ctc-3d-printer-owners/forums/general/topic:36103#comment-2453802 ***the thermocouples I used***...