ctc i3 clone parts 3d models

Available Replacements A "Replacement Parts" section can be found in our store, featuring an extensive range of components designed to keep your devices in top condition. Whether you're looking for a new battery, charger, or any other essential...

Print Settings Printer: CTC i3 Clone Rafts: No Supports: Yes Resolution: .2mm Infill: 20% Notes: If I were doing this over again, I'd bring the angled back all the way down to the bottom so it won't need any supports while printing. ... Category: 3D...

I designed a custom enclosure to house a CTC i3 Clone, relocating its electronics outside of my main build space. To position the display optimally, I chose to mount it vertically, bringing the screen to eye level for comfortable viewing. ...This...

This badge will snugly fit into the pre-drilled holes found on the Reprap Prusa I3 plywood frame, where a clear serial number tag once resided. ...The hole spacing measures 64mm, suggesting it may also suit other printers of similar design.

This part needs to be rotated to ensure proper assembly on my Prusa i3 clone.

This is a straightforward guide to setting up your Anycube I3 clone from CNC. ...Several other filament guides existed before mine, but none of them got the screw spacing just right – about 15.8 cm apart.

Print Settings: Printer: CTC i3 Rafts: Not Required Supports: No Support Needed Infill: A recommended 15% or higher infill setting ensures optimal print quality and minimizes pillowing. Notes: To ensure a successful print, pay close attention to...

I combined two excellent upgrades to improve the Prusa i3 Clone, a 3D printer available on eBay. The cheap motors I was using were holding me back, so I made some key changes. ...First, I removed weight from the extruder by integrating the Bowden...

A compact tool holder for the CTC tool plus caliper and pen.

I swiftly tidy things up, ensuring all wiring is neatly arranged and no longer obstructs anything.

This part fits perfectly onto your CTC Prusa i3 Pro B Clone. You can use it in combination with my E3D assembly, which is available on Thingiverse at https://www.thingiverse.com/thing:2347773 and https://www.thingiverse.com/thing:2344418. ...The CAD...

The parts work seamlessly with ModelStation's excellent cable chain, available on Thingiverse under ID 11978. I designed them to fit together perfectly but printed each component using a scaling factor of two-thirds. Next, I drilled a 10 mm hole into...

... Accompanying Carriage. ... Changes: * X-Axis Bracket part: * Removed screw-rod guide to support anti-wobble pads. * Added screw holes for Hall endstop. * Tweaked wire tunnel for the endstop sensor wires. ... * Made minor adjustments throughout.

Filament Guidance for the CTC-DIY Prusa i3 Clone To prevent the filament from escaping or jamming in the wooden frame over time, this guide can be attached to the frame. Those not satisfied with print quality can purchase a conversion kit for the...

I've got a cheap eBay i3 clone that's broken its X-axis belt pulley holder. I couldn't find a replacement part that fit, so I decided to try drawing it up in Rhino. The holes for the bearings are 8mm in diameter with no play and are intended to be...

I have a CTC i3 DIY 3D Printer I bought from eBay. It runs off a clone of the Geeetech 2560 (GT2560) Revision A board. Sadly they neglected to put a bootloader onto the board, and as such I was unable to upload any new firmware to it. I looked...

This Bowden setup is specifically designed for the CTC DIY I3 and includes two main components: - The part you are currently viewing - An extruder mount that can be found at https://www.thingiverse.com/thing:2942200 Alternatively, users can opt for...

I was approached by a member of the CTC group on Facebook to adjust the original Joox design for the new 6mm Frame version. A test print in 6mm has been included, allowing users to check fitment before proceeding. UPDATE: On March 1st, 2018, it was...

Later, I designed and printed some parts (which I show individually in each post). In this post: 1 - Y-axis motor support with screw for anchoring to the support surface. I noticed that when tightening the Y-axis belt, the back plate, which...

CTC Prusa i3 (clone of the Geeetech Prusa i3 Pro B) official parts & other contents from SD card.

Assembly help for the heating bed, nothing too crazy, you just press an M6 nut into the middle and swap everything out against the wing screw. ...// Update, now only 20mm diameter, otherwise it won't fit when the bed moves all the way forward.

CTC Prusa i3 clone ships with official Prusa i3 (Geeetech Prusa i3 Pro B) components and loads additional content from an SD card.

I'm using a CTC I3 Pro B that comes with an 80/20 frame set.

You can use 10x 30mm bolts to consolidate fixings without worrying about fouling the print or other parts. Alternatively, you could acetone weld the halves together if using PLA; this may add strength but I haven't tried it or found a need. Any...

... but I've found it unnecessary since I've set the dimensions so that the extruder gets snugly secured and grips the filament perfectly. If I end up disassembling this part again in the future, I'll be sure to note down the screw lengths required.

... at 102% scale with Ultimaker Cura settings optimized for your printer. The recommended printer is the CTC I3 PRO B CLONE PRUSA, which delivers exceptional results. ...Mid-print, pause at 75% completion and add M3 nuts to secure the piece in place.

... with this setup; however, I cannot guarantee its performance on your system. This information is supplied without warranty and serves as a guideline for upgrading your 'CTC Prusa i3 Pro B DIY.' I am not familiar with other brands of the i3 model.

This is a remix of the awesome AM8 frame by pheneeny (https://www.thingiverse.com/thing:2263216) , I found that the CTC Pro I3 B (or whatever its called this week as the name changes frequently) does not share all the same parts as the Anet A8 this...

This upgrade enhances the CTC Prusa i3 DIY, enabling use of a MK8 extruder as depicted in photos ($24.95 on eBay). The only wiring modification is swapping the middle two wires connected to the stepper motor. The print head is positioned about 1.5...

This is a remix of the awesome AM8 frame by pheneeny (https://www.thingiverse.com/thing:2263216) , I found that the CTC Pro I3 B (or whatever its called this week as the name changes frequently) does not share all the same parts as the Anet A8 this...