ctc i3 clone parts 3d models

... from My Printer. ...I'll Use Small Plastic Bags to Contain All the Debris, Keeping the Printroom and Floor Clean. This Setup Works on My CTC Bizer, So It Should Also Function on My Makerbot Replicator 2X Without Any Support or Raft Needed for Printing.

Case holder specifically designed for the CTC Riverside SLA printer, constructed with robust components. Fastening hardware consists of eight M4 screws with a length of eighteen millimeters. Print settings are configured as follows: Supports are not...

... ...Follow the instructions below to customize it further: Options: - font_thickness: 5 - stick_thickness: 3 - hole_radius: 3 - Font: write/Letters.dxf - message: CTC COSMO 2010 - stick_width: 8 - font_size: 10 - flat_bottom: 1

I scoured the internet for an angled display holder that would perfectly complement my CTC printer, but every option I came across was subpar. The only one that caught my eye was a design on Thingiverse: https://www.thingiverse.com/thing:2057624. ...So,...

================================================================== Just another set of feet for the CTC printer. Although there are numerous feet available, none of them suited my needs or matched my aesthetic preferences. They were designed to...

These feet are designed for a black CTC (dual) printer, specifically where the lowest side panel screws are positioned 25mm above the table. The STL files provided are actually adapters to attach standard 30mm rubber feet, such as door stops from...

... the wood case or drill it larger and use washers and nuts. Following settings worked fine for me on a CTC printer. ... PLA Filament 230°C Nozzle / 120°C Heat bed (blue taped) 3 Shells / 15% Infill 0.1mm Layer height 130mm/s speed while extruding

Options used include stick thickness of 3, font thickness of 5, 'write/Letters.dxf' font type, flat-bottom setting enabled, stick width of 8, the message "CTC VAD 2016", font size of 10, and hole radius of 3. ...

This is my side spool holder for the CtC printer, as you can see from the photo it's simply hooked onto the side walls of the device. Three elements are available for this holder, each marked with "left" or "right" to ensure correct placement on the...

... for each foot is recommended. The conical shock absorbers can be sourced from eBay or by visiting a music store and purchasing conical speaker feet. These will provide the necessary support for your CTC printer. ... Print without support and enjoy!

I attempted to upgrade my CTC creator printer's Z-axis stabilizer but it just wouldn't align properly. The print bed collided with the bearing housing support frame, making it impossible for the print head to reach home position in the first place.

A slight modification of Thingiverse's design number 351280 enables installation on a CTC A8 with a 40mm fan. The support piece has been extended for this specific placement at the back side. To secure it properly, the fixing screws on the metallic...

... ...The specifications used in this customization include a stick width of 8, flat-bottom enabled (value of 1), hole radius of 3, message "CTC PS 2014", stick thickness of 3, font size of 10, and the "write/Letters.dxf" font with a font thickness of 5.

Customize the options to display "CTC CST 2012", use sticks with a width of 8 and thickness of 3, font size of 10, hole radius of 3, font thickness of 5, and use the 'write/Letters.dxf' font. ...Ensure a flat bottom by selecting the 'flat-bottom = 1'...

Accessible via http://www.thingiverse.com/apps/customizer/run?thing_id=52734, this item features specific settings such as flat_bottom = 1, stick_width = 8, message = CTC CA2 2016, hole_radius = 3, stick_thickness = 3, font_thickness = 5, font_size =...

This is a set of four small pieces that can be used to repair a CTC DIY-Prusa-Printer on a wooden desk, similar to an IKEA Lack-table. ...The tiny fixings are situated on the front of the printer, securing the large screw rods both to the left and...

Plexi Enclosure for CTC or similar models. I sourced the hinges from thingiverse and adapted them to my plexiglass sheets. In my case, they're made of 2.5 mm Plexi. ...I also made hinges for 5 mm Plexiglas, once for M4 screws and once for M3...

Below are the instructions for creating this unique piece with the following options: flat_bottom = 1, font_thickness = 5, stick_width = 8, hole_radius = 3, stick_thickness = 3, using the Font "write/Letters.dxf" and a font_size of 10, resulting in...

... ...The printing settings include a flat bottom, 8mm stick width, and the message "CTC CA2 2014" printed on it. ...The hole radius is set to 3mm, with 3mm thick sticks, 5mm font thickness, 10mm font size, and using the 'write/Letters.dxf' font.

... For fabrication, set stick width to 8, enable flat bottom, hole radius as 3 and customize the message as "CTC PS 2016". ...Set stick thickness to 3, font size to 10 and use 'write/Letters.dxf' font with a font thickness of 5.

Instructions for customization include setting font thickness to 5, inputting the message "CTC Margie CST," choosing the "write/Letters.dxf" font, setting stick width to 8, stick thickness to 3, enabling flat-bottom option with a size of 10, and...

... of the original design. A new Cable Height adjustment mechanism was designed by Construkt, ensuring correct height alignment when used with the Cable Cain Extruder Holder 5 Test. Print Settings: Printer: CTC Bizer Resolution: 0.20 mm Infill: 30%

Using the following options: Message is CTC ChildCare 17 Stick thickness is 3 units Flat bottom option is set to 1 unit Font used is write/Letters.dxf Font size selected is 10 units Stick width chosen is 8 units Hole radius set to 2 units Font...

... For this specific version, stick width was set to 8 and stick thickness to 3. The chosen font is "Letters.dxf" with a thickness of 5 and size of 10. A hole with radius 3 was also included and the message on the object reads "CTC HOT 2014".

Printer Identification Number (CTC) Confirms Compatibility with Current Model. Raft Options Set to Disabled, Enabling Direct Printing on Desired Surface. Support Structures Disabled for Maximum Flexibility. Resolution is Set to the Optimal Value of...

This is an Improved Clip Spool Holder for the CTC Replicator. I created this modified design to attach easily to either the left or right top of the printer case using clips. Four additional clips provide extra stability. You may need to fine-tune...

For specifications, the font thickness is set to 5, stick thickness to 3, hole radius to 3 with "CTC Childcare 15" as the message inscribed using a font size of 10 and stick width of 8, all displayed on a DXF file named 'Write/Letters.dxf' and...

Here is the text rewritten: A Simple CTC Flashforge 3D Printer Cover fills a vital gap at the rear of the printer, specifically designed for the small hole where the filament spool holder resides. This clever solution addresses a common issue: when...

This is a cutting-edge bowden conversion kit consisting of sturdy support brackets for a CTC printer utilizing a RepRap 3D Printer Dual Input Dual Nozzle Bowden Extruder Hot End 0.4mm 1.75mm. The innovative design places the nozzle just off-center...

I chose the message: "CTC HOT 2017," stick thickness: 3, flat bottom: 1, Font style from "write/Letters.dxf" with font size 10, a stick width of 8, and a hole radius of 2. ... Note that your specific Hot Cocoa Thermos may vary depending on the options...