cuban chain 3d model

I have left the original design files as well to preserve version control. Design File Included: .f3d, .ipt, step, .skp, and .obj files. Follow The Makers Workbench...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_radius = 6 custom_top_port_corner_radius = 5 custom_back_extra_port_y_position = 30 pattern_line_thickness = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

phone_model_customized = Yes, it is now set at 0 custom_left_port_y_position_disabled = No, has been set by the default of 0 as requested above bottom_port_corner_radius_customization_enabled = Yes, now has a custom setting equal to 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

I recommend 3 loops since this is quite a small model. Otherwise not enough PETG is dumped before the start of the parts</p><p>Print bed recommendation: Powder coated steel sheet with glue stick. I usually just put a 5cm to 10cm light line on the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Licensed models were manufactured in Germany, Sweden and Russia First Fighter The Type L is famous for being used by Roland Garros to shoot down three German aircraft in April of 1915. This was a special single-seat arrangement made for the tennis...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

I recommend using a shorter heat sink and/or a fanBe sure to choose a fan size that will not interfere with the height of your heat sinkFilament sensor fits without issueBondtech extruder fits without issueOnly other fitment issues I have heard have...

&nbsp;For me, it pressed in very tightly; if in doubt, glue it in.To mount the holder, I stuck this adhesive mount onto the back, and used it to replace the jaws of an older model of this suction base. &nbsp;The adhesive mount’s socket is smaller...

This is a well known test model with many remixes.However, I have not seen anyone with automatic temp range.Existing temp tower is “semi-automatic”, they set temperature to preset levels with custom g-code in “before layer change”This print set...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

A great way to combat this on any print with sharp corners is to add “Mouse Ears”.• Add these in PrusaSlicer by right clicking on the model in the list on the right of the screen, hover over “Add Part” and select “Add Cylinder”• With the cylinder...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

Those are only used to ensure consistency and are not necessary for rendering the model. I also pulled in the 40mm Fan Grill from the Sanginololo case and copied it here to make it easier to find. Those little 40mm fan grills print really nice and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

... (option code 772). From VIN F060888 1999 Mercedes-Benz CLK430 Base Coupe 2-Door 4.3L 4266CC V8 GAS SOHC Naturally Aspirated Included formats: *.obj, *.stl, *.3mf All dimensions are accurate. This model printed and tested successfully.

Related models: Track connectors for wooden railway to Plarail (and other systems) https://www.thingiverse.com/thing:5024058 Various other items of rolling stock: https://www.thingiverse.com/densha/designs Note that many 0-gauge (O-gauge, 32mm...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The COMPLETE Requiem Brotherhood bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Requiem Templars (presupported) Requiem Templars stand before the chaos and...

For now I have modelled two trailers:mk14 flatbed trailer for general loads, 10' and 20' ISO containers.mk17 tray-style trailer with hydraulic crane. Can carry 1x 10' ISO container, or general loads. Tray sides are removable.mk14 trailer can also be...

The most common ones used for model rockets were very pricey and hard to find in bulk. I did some research online and found a couple of people having success with pencil graphite, so I started experimenting using an 18V drill battery as my power...

(I have included a model with logo, and one without)Assembly Instructions:Print the box and two clipsInsert bowtie shaped post on clip in to corresponding hole on box, then rotate until the push-clip lines up with the hole.Push the push-clip in to...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

This is a modification to the SlideSnap Pro: https://slidesnappro.com/ At the time I bought a SlideSnap Pro, they had two models, the SlideSnap Pro, and the SlideSnap Lite. Both are based on a refurbished and modified Kodak carousel projector. The...