cube 2 hypercube reddit 3d models

Sturdy hotend holder with integrated cooling channel for Hypercube type 3D printers. The original part allowed for some play after a few prints. Use 4x20mm wood/sheet metal screws for assembly. Did the model help you out? ...Sponsor me a cup of coffee...

This is an innovative Hypercube extruder mount designed for seamless integration with a 3in1out NF THC-01 extruder and a precision-crafted LJ18A3 proximity sensor. ...The unique design carefully positions these components in tandem, allowing for optimal...

... in marlin. ...Configuration is for a Hypercube Evolution but can be used on a Prusa I3 type printer with minimal modification. I used the spring from a pen to keep the tension on the extruder mount. ... https://www.youtube.com/watch?v=RACh7JfYsy0

Mounting Plate Designed for Hypercube Evolution with LM10LUU Bearings. This plate was created because a standard mounting plate between the carriage causes wobble, which in turn reduces printing speed. To install the Hemera mount, use three M3x8...

Brackets for Hypercube evolution with 3030 extrusions. I also designed a piece that acts as a spacer for the extrusion that supports the z axis, with the 10cm used in the original model of the Hybercube Evolution. ... It is intended for use with m5...

Mount the heated bed onto the 20mm extrusion for the Hypercube Evolution using brackets. ... To attach the heated bed, I needed to create a custom bracket due to its unique bolt hole pattern that didn't match any of the existing brackets.

Create a trim panel with counter sunk holes designed specifically for mounting onto a 3030 extrusion system, featuring 100mm lower bar spacing on the Hypercube Evolution. This custom trim panel is tailored for use with a 300x300x300 chassis, ensuring...

I crafted this Z-Nut Mount to supercharge my Hypercube 3D Printer's performance. ...This innovative design streamlines angle correction and simplifies position alignment, making it easier to achieve precise results.\r\n\r\nTo build the hinge, I require...

When constructing my HyperCube, I deliberately placed the 90-degree brackets right up against the base of the framework, ensuring that the part identified as thing:1888967 wouldn't be able to fit in place. ...To resolve this issue, I imported the STL...

Chimera extruder with BLtouch mount for the Hypercube Evolution, redesigned from Scott's original design. I engineered the BLTouch mount to utilize the same brass insert as the Evo BOM. Note: This is an ongoing project and has not yet been...

With the original mount I could not achieve this dimension. This is a remix of einarms's Bltouch Mount Hypercube Evolution. The shank length is lengthened and the sensor flange thickness is reduced to allow additional adjustment ability.</p> <p>A...

Aug-21-2021: Added z-axis-align-300 for the Hypercube 300 V1. It needed to be a little thicker. ================================================================= https://www.thingiverse.com/thing:4441076 Simple leadscrew holder to provide...

Requires *** - M3 x 12 mm screws - M3 x 10 mm screws - 5mm x 5mm x 5mm brass inserts - 5mm x 5mm x 5mm cylindrical magnets for top cover - 2 x 40 mm turbo fan (part cooling) - 1 x 40 mm fan (cold end cooling) Printing *** Most of the parts have...

probe temperature compensation: https://github.com/MarlinFirmware/Marlin/releases/tag/2.0.2 Temperature calibration: https://marlinfw.org/docs/gcode/G076.html Marlin config: #define TEMP_SENSOR_PROBE 1 #define TEMP_PROBE_PIN 15 //TEMP_1_PIN #define...

I designed the simplest possible bracket to hang an E3D titan on a Hypercube, excluding any fan brackets. A straight bracket is sufficient to provide support for a 50mm blower. I am satisfied with the design. Two holes are provided under the...

This bracket enables mounting a Hall Effect sensing circuit onto an 8mm linear rod; I designed this with OnShape and TinkerCAD to replace the mechanical endstop on my HyperCube printer. The clamp portion of the bracket was taken from Tech2C's...

I fell in love with the Spoegler design, so I decided to give it my own spin by remixing it to fit my Hypercube Ngen perfectly. The X carriage is completely brand new, minus the magnets and connector found on the original - a deliberate choice made...

Mounts for the bed cablechain on my Hypercube Evolution. The frame mount is modeled to fit a 3030 extrusion and the mount on the bed fits a 2020 extrusion. The cable chain has a width of 200mm. Print Settings Printer: Hypercube Evolution Rafts: No...

I came up with a system that I consider valid enough, so some pieces of the original HyperCube Evolution should be reprinted - like the X carriage. However, other parts such as the right Y carriage and its clamp can be modified with a drill bit to...

I designed the HyperCube Evolution from SCOTT 3D (https://www.thingiverse.com/thing:2254103) and incorporated parts of my anet a8, which is why I chose a double axle with 8 mm to reuse many existing parts. The hypercube evolution is a fantastic...

Key considerations when printing this bracket: Printer: Hypercube Rafts: No rafts are necessary Supports: No supports required Resolution: .20mm resolution is sufficient Infill: 20% infill density should be used Additional notes: A total of three...

Built upon the original Hypercube Evolution, it boasts improved part designs modeled in Solidworks to ensure perfect alignment and fit for the GT2 belt to remain horizontal throughout carriage travel. The motor mounts and idlers enable easy removal...

Created a LED strip holder to fit the need of my 600x400x440 Hypercube Evolution on 2020 Aluminum Profiles I have uploaded the STEP files for your customization needs. The files uploaded are 4 sizes: 177.50mm 137.00mm 185.00mm These...

Here is another straightforward autoleveling passive mechanism for hypercube. These are parameters for Marlin configuration: Distance from hotend: X coordinate is set to -41.5mm, indicating the hotend is positioned 41.5mm to the left side. Y...

This is a more robust stepper motor mount for the Hypercube Evolution. I encountered an issue with my mounted motors (using the original mount) producing some severe vibrations that were visible on the outer shells. This mount employs a square nut...

Two parts from the HEVO project which I have modified to fit as an upgrade to the original HyperCube. Hotbed clamp for Z axis - easier to print as one wide is completely flat so it fits the outside of the bed's frame. This allows to fit it without...

I've designed a custom Hypercube Evolution with twin Z drives that boasts an additional 30x30 rail on both sides, conveniently positioned 105 mm beneath the top rail on my particular setup. This unique feature enables me to securely fasten an Arduino...

Remix for my Hypercube. Bed was from a Tevo Tarantula. Just press - pound in the old nut. (I used a rubber mallet) https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO...

This setup is specifically designed for the Hypercube Evolution but can be easily adapted to a Prusa I3 type printer with some minor adjustments. I employed a pen spring to maintain the tension on the extruder mount, ensuring everything stays...

This build closely resembles Tech2C's XY Joiner for HyperCube, but I've taken it a step further by incorporating extra X rod support and enlarging the idler areas to accommodate geared idlers. With tight belts, the X rods may slightly deviate from...