cube flight controller 3d models

Remixed for matek 743 wing v3, matek gnss M10-5883

Here is a simple cockpit designed specifically for a Ranger EX. To assemble this design, you will need two side panels as well as one each of the bottom, middle, and top plates. If you prefer to secure your cockpit with double-sided tape or glue,...

Remixing the MKQV C1 FC Deck with its signature 30.5mm and 20mm hole spacing to seamlessly integrate with the original deck supports, now readily available from the iTSV C1 Chaser Parts line-up.

Testing reveals that the 30.5 Hole Pattern is a crucial aspect of a custom Mavic build, requiring the removal of rubber O-rings from sensor housing locations. ...The Mavic assembly then seamlessly snaps into place, fitting snugly within these precisely...

Setup Tasks: The Arduino Due boards show up with identical USB names and device IDs, which can cause problems if you're using more than one panel. I've seen DCS switch back and forth based on how the game loads up the panels. Dakor91's comment on...

I recently opted out of my bulky daitone PDB setup, choosing instead to downsize with a more compact one. To keep my naze secure, I needed a new housing that would seamlessly integrate with my already soldered board. That's where this custom-designed...

highly effective vibration dampener for high frequency vibration. use with naylon screws. 4 pcs required. ...

This is a bracket for the KK 2.1's buzzer, secured by arm mounting hardware. ...A countersink in the screw hole limits it to just 1 millimeter deep, making standard frame screws sufficient.

adapter to mount FC diff sizes

In version 2 of the KK2.0 Case, M3 screws now securely fasten the KK2.0 to both the upper and lower parts of the case. The overall thickness has increased from 1.5mm to 2mm, with each part receiving new dimensions or designs. The global measurements...

Mounts easily with just a single M3 screw, snuggly securing it to both pancake 1 and pancake 2 quadcopter designs, while remaining adaptable for use on other models as needed.

Humans need a way to easily install their ESC and FC. ...We've got just the thing - this comprehensive kit has everything they'll need to get started.

The individual modified the hole size to 30.5mm x 30.5mm, resulting in a more precise fit, and also created hot glue receptacles at the base.

The measurements require slight adjustments as they are quite fitting but could be more snug; also, the screw hole alignment is off.

A concept submitted by a viewer has sparked the potential for this design to undergo revisions based on user input and subsequent feedback.

This surround is specifically crafted to fit snugly around the stand-offs on my ZMR 250 Quadcopter frame, safeguarding the delicate electronics within. A precise aperture allows easy access to the USB port on one side, while a lower opening...

FC Specifications MCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB Flash Board V1.0 IMU: MPU6000 (SPI1) & ICM20602 (SPI4) Board V1.5 IMU: MPU6000 (SPI1) & ICM42605 (SPI4) Baro: Infineon DPS310 (I2C2) OSD: AT7456E (SPI2) Blackbox: MicroSD...

This is a 30.5mm to 20mm FC adapter. The 20mm mounting uses 2mm screws and can be tapped as is. Fits my Xrotor nano stack perfectly! ... Category: R/C Vehicles

Customized version of https://www.thingiverse.com/thing:189264 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=189264

This simple guard clicks onto the FC vibration dampeners to stop debris from accumulating on the FC when running motors/props in reverse rotation mode. It will work effectively on any quad using an FC with 30.5mm mounting holes, provided ESC wires...

This is a highly adaptable converter that enables mounting 20mm components within a 30.5 mm stack and vice versa with complete flexibility. Users have the option to include integrated spacers on both the top and/or bottom of the 30.5mm and/or 20mm...

Very simple case for Omnibus F4 Pro v3.

Simple remix, needed it a little stronger and thicker. ...With everything attached the arms on the original snapped right off.

This is a design for my Strix Goblin easy FC install tray. I've included a 'basic' version with the minimum required parts to make this work, so you can create your own variation. The full version includes all the necessary components specifically...

Nazgul5 v2 dust cover

This holder is specifically made for the KK 2.1's buzzer, using the arm mounting hardware that comes with most frames. To install it, simply screw it into place - the countersunk screw hole is only 1 mm deep, so you shouldn't need to use longer...

first part screw hole to hole 30mm * 30mm ------ The other part screw hole to hole 35mm * 35mm

Remixed parts from dmxkov, adapted for pilots flying on analog video. There are places for FC [25x25 mm], VTX [30.5x30.5 mm], GPS and quick-release connectors for wings. Under VTX, I installed a PC fan 40 * 40mm just with glue. Maybe someday I'll...

Weight is critical when performance is key: This lightweight unit tips the scales at just 4.4g and can be securely fastened with four rugged M3x8 nylon screws. ...It measures a compact 39.2 x 8 x 39.2 mm, making it an ideal fit for any design requiring...

3d scan with individual components for your customization pleasure, bonus FC tray that attaches to inner CF spars. Tray is designed to work with MATEKF411WTE and gives it a nice location, currently in Mk1 and still in testing, it positions the...