cubicle purse hook 3d models
55059 3d models found related to cubicle purse hook.thingiverse
My wife asked for a purse hook she could hang her purse on it so she would not have to set it on the floor. ... hang hook on edge of table, put purse strap in small hook
myminifactory
This is a simple hook that clips on to the center console so you can hook a purse off it. This prevents the purse from falling over and spilling out on to the floor. ... Designed for the 2015 Honda Civic.
thingiverse
The fact that their's has the forward angle forces the center of gravity towards the desk and thus keeps the hook on the table. The issue I fixed with it is adding the rounded surface that the bag handle hangs from and also removed the angle...
thingiverse
Based on the standard design of the old good https://en.wikipedia.org/wiki/Purse_hook I wanted to print one for my wife but couldn't find it so I tried to make it on Tinkercad. This is my first submit so I know there is still a lot of room for...
prusaprinters
I based the shape off of https://www.thingiverse.com/thing:2269715.The fact that their's has the forward angle forces the center of gravity towards the desk and thus keeps the hook on the table.The issue I fixed with it is adding the rounded surface...
thingiverse
Clip on cubicle coat hook for 2" x 5/8" cubicle trim. ...The .sldprt file is from Solidworks 2013.
thingiverse
Designed for common cubical walls, this is a fairly stout hook for hanging coats, purses etc.
thingiverse
This is a cublicle hook that will fit over a cubicle wall that is 2" in thickness.
thingiverse
Hook that fits office cubicle walls. Also, fits IKEA KURA bed rails. ...Print Settings Notes: In metric system.
myminifactory
A simple hook, attaches in the cubicle rails. ... Super strong--I use this to hold my backpack, messenger bag and even my coat in the winter.
thingiverse
This is a double hook which can be plugged onto an office cubicles walls. The walls have a diameter of approx. 53mm. ... Printed in simple PLA
cults3d
This is a double hook which can be plugged onto an office cubicles walls. The walls have a diameter of approx. 53mm. ...Printed in simple PLA
thingiverse
... picture with details. You may also like my: [Cubicle headphone hook](http://www.thingiverse.com/thing:3379500) [Cubicle wall phone bracket](http://www.thingiverse.com/thing:794020) [Cubicle wall card clip](http://www.thingiverse.com/thing:2780328)
thingiverse
... Instructions Print; cleanup; use! [2011-07-28] Added "cubical_hook_with_loop"; this has a hook at the bottom to hang the headphone cable on. [2012-08-02] Added "newcube_hook"; we have some new cubicles, so time for a new hook.
thingiverse
The hooks posted here are for 54 mm-wide (about 2 1/16") cubicle walls. ... Print Settings Printer: VERTEX K8400 Rafts: ...
thingiverse
... to MatthewGTaylor and fiveseven808 for the awesome base model! ... I've modified fiveseven808's design to work with the cubicles my office has. I found that fiveseven808's design was great, but the hooks needed to be moved back to fit the uprights.
thingiverse
This is a cubicle hook for a 50 mm wide cubicle wall. I made the inside dimension 55 mm to give it a little room on each side. With a 50% infill this thing is pretty sturdy. It can handle quite a bit of weight. I uploaded two versions,, one with...
thingiverse
Found that the hooks that clip onto the top of the cubicle wall were a little hard to find, so I decided to borrow one & copy it. Took some measurements & made this my first ever project in Fusion 360. I purposely did not make it banjo-tight...
thingiverse
A hook for your cubicle wall. Designed for a top bar that is 2 1/8 in. (~54mm) wide and 1/2 in. (12.5 mm) high. Snap the back in first and lower the front into place. This STL is for a hook with a width of 10 mm. Increase the z scaling (it is...
prusaprinters
Found that the hooks that clip onto the top of the cubicle wall were a little hard to find, so I decided to borrow one & copy it. Took some measurements & made this my first ever project in Fusion 360. I purposely did not make it banjo-tight...
thingiverse
rotates and snaps into rail of cubicle extrusion. Print Settings Printer Brand: Up! ... Printer: Up Plus ...
myminifactory
This is a dual hook for a cubical office. The hook was designed in OpenSCAD so that it can easily be modified to the proper cube thickness. It could also be easily modified to add more hooks or make them side by side. The possibilities are...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/h4SmCpPxv5d Made with narrower hook width.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1367661 Instructions Using the following options: extremity = 0 stop_lenght = 15 second_hook = 0 spacer_4 = 5 spacer_3 = 5 spacer_2 = 5 spacer_1 = 5 thickness = 20.1 second_hook_lenght = 30.1...
thingiverse
Fits 10mm deep rack channels. ...The large hook is strong enough to hang a coat on if it is printed with 5 walls.