curtain pole holder 3d models
344028 3d models found related to curtain pole holder.thingiverse
There is two version of it: - One version for thinny poles up to 1/2 in (12mm) - One version for poles up to 3/4 in (20mm)
thingiverse
Fit 35mm diameter pole, 2x 5mm screw hole support, 30mm width, 135mm length, 80mm height. If you would like to donate, visit this link paypal.me/sham2951. Thank you. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
Curtain pole holder for shutter box. For 2 cm diameter curtain pole. Clip to shutter box. ... No screw required
thingiverse
from https://www.thingiverse.com/thing:1648559/files but customizable
thingiverse
Customized version of https://www.thingiverse.com/thing:3699558 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3699558
myminifactory
Bathroom curtain hangers and pole holder Very easy to print! Just plug and play, no need for support! ... For more information check out my profiles: https://linktr.ee/3DPrintingDoctor
thingiverse
This is a curtain pole support that is used for the middle of the curtain pole or can be used for connecting two poles together.
thingiverse
Curtain pole bracket for 13mm poles. ... Printed with a thick wall (I did 4mm) and 10% infill
thingiverse
Needed something to hold the pole for the curtains on a permanently mounted fixture
thingiverse
Adding curtains to the patio doors, I wanted the curtain to be inside the alcove to hopefully preserve the heating. ...So I made this Curtain Pole Ceiling Mount, I made in ABS , works and looks great.
thingiverse
This holder attaches to the wall with double sided foam tape and allows the pole to be supported without it being able to slip out. I suggest using the permanent outdoor double sided tape instead of the indoor type. ... I used PLA at 200C with 75%...
prusaprinters
This holder attaches to the wall with double sided foam tape and allows the pole to be supported without it being able to slip out. ...I suggest using the permanent outdoor double sided tape instead of the indoor type.</p> <p>I used PLA at 200C with 75%...
thingiverse
I made a few different spacers to cater for larger/smaller curtain hoops to give more clearance behind the pole to the wall. I also provide the spacers separately for more flexibility. The hole through the bracket is 7mm and is countersunk...
thingiverse
Its designed to be a little bigger and stronger than the usual bit of bent metal you get with curtain poles for use in bay windows. In a bay window the pole can twist and droop if it can move in the curtain pole support. Print Settings Rafts: Yes...
thingiverse
Super simple curtain pole bracket, designed to replace a broken plastic one from Ikea with same dimensions. Will hold pole up to 25mm diameter. Screw holes are 4mm. Printed flat with no supports, 10% infill in PLA. ...Was meaning to set infill...
thingiverse
This thing is for those cheap curtain poles that droop down at the corner, causing the shower curtain to slide away from the wall, leading to a gap and potentially a soggy floor. This thing simply clips snugly over the pole (approx 20mm diameter),...
thingiverse
This is quick hook i designed to hold the christmas star designed by Paul M https://www.thingiverse.com/thing:35866 It Enables you to pass some string or a power cable and hold in place, and then hook it over a 25mm metal curtain pole as window...
thingiverse
Curtain pole laser mount 29mm inner diameter. Designed for m3.5/m4 screw up to 12mm long. ...
thingiverse
A bracket that the bottom plate of a Tapo camera can be screwed to. ... Curtain pole size is 19mm diameter.
thingiverse
for use with 28-30mm curtain poles (the sort used for eyelet curtains). I printed the first 10cm at a very high infil (80%) to provide enough strength. Later laters were printed with less infil. You will (probably) need support material for the...
thingiverse
bracket for citroen berlingo multispace (2007 model) that allows the holding of a 15mm diameter pole. ... *DOES REQUIRE DRILLING / SCREWING INTO THE PLASTIC AND METAL BEHIND IT TO BE ABLE TO MOUNT*