custom borosilicate glass sheet 3d models
1200891 3d models found related to custom borosilicate glass sheet.thingiverse
Borosilicate glass stopper from RenRen3D FlashX Pro 3D printer. Glass size is 230mm and thickness 4mm. Hexscrew diameter is 4mm. ...Print Settings Printer: RenRen3D FlashX Pro ...
thingiverse
Borosilicate glass stopper from RenRen3D FlashX LT(LX) 3D printer. Glass size is 210mm and thickness 4mm. Hexscrew diameter is 3mm@15mm. ...
thingiverse
Designed for the Afnia and UP Plus printer and the Borosilicate Glass Platform available from Octave. Permanently attach to back of heated platform with a single screw at the center. ... Glass slips under the clip to secure at the back, secure the...
thingiverse
I like to use borosilicate glass plates to print on. I also like to use different surface coverings depending on the material being printed. Therefore, I have several glass plates in both 1/8" (3.3mm) and 1/4" (6.6mm) thicknesses. I created this...
thingiverse
I've been thinking for a while how I can fit a larger borosilicate glass to my 200x200mm heatbed. I mostly print PLA so it is not critical if some parts of the print are not heated. I modified my printer to have a larger print area...
thingiverse
I liked the mounting from this: https://www.thingiverse.com/thing:2217881 and I needed the geometry for my borosilicate glass from this: https://www.thingiverse.com/thing:2253400 The combination works fine for me. My glass pane has the dimensions...
thingiverse
Some clips that I made to hold my borosilicate glass plate to my bed.
thingiverse
... to fit their glass plate. Here is a link to the glass plate I purchased on Amazon [Ogry MK23 Heated Bed Borosilicate Glass Plate Size 300X200X4mm](https://www.amazon.com/Borosilicate-300X200X4mm-Printers-Accessories-Toughened/dp/B07DNTC71W/).
thingiverse
I found for a long time that I sometimes forget to clip the glass at the front and I have broken more than one sheet of glass this way, when the glass slides off the front down to my concrete floor. I have fixed that in two ways: I installed a foam...
thingiverse
Updated 02-14-2017: Replaced damaged STL file This is a modification of my clips to hold an inexpensive 11" x 8.5" glass plate to the heated bed of a Replicator 2X -> http://www.thingiverse.com/thing:1908836 These clips are designed to hold a 200mm x...
thingiverse
After struggling to find a clamp for my borosilicate glass panel for my SnapMaker hot bed and having all the metal clips purchased from popular internet market places eventually snap i decided to look for alternatives. Bulldog clips were too bulky...
thingiverse
WIP: I looked to a thing to hold the borosilicate glass on my G2S but anything I liked needed me to disassemble the bed, so I decided to play around and create something that would allow me to hold the glass, without having to disassemble my G2S. ... I...
thingiverse
However, the glass clamps I found online were for 16" table glass, which is what I was using previously, and were also not adjustable and not sized for 348mm round sheets of glass that I was switching to. So I set out to design these clamps that...
thingiverse
Corners for use around borosilicate glass 310x310cm on Artillery Sidewinder X2. ... To remove the foldback clips on glass (they hit nozzle) You need to 3D print 4 units and glue them with double-sided tape like 3M™ Acrylic Foam Tape 5mm Note : one side...
thingiverse
I recently switched from hand cut 1/4 inch plate glass to 200 mm X 213 mm X 3 mm Borosilicate Glass Bed and needed better corner clamps to hold the glass & bed heater in place and accommodate easy leveling. My 1/4 inch plate glass plates kept...
thingiverse
But not before I scraped up the glass, which the manufacturer did not tell me to do. Thanks, Creality. A few objective for me: Use the overpriced glass. Open up space on my desk below my laptop. Find a place for me to cool mirrors, as I print a lot...
prusaprinters
This is my first original design here! Yeah, so I ordered the Ender 3 and the glass. But, then I realized that mirrors were better for me. So, I cancelled the glass and bought mirrors. Well, they didn't cancel the glass. Turns out, I still like the...
thingiverse
There is also versions adapted for smaller glass than aluminium, And a special version made for the PowerSpec 3D, "special raised .25" is the nickname, but we are still improving through successive versions, latest being V5 Instructions You'll need...
thingiverse
Customized version of http://www.thingiverse.com/thing:43783 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=43783 Instructions Using the following options: height = 3.17
thingiverse
You can now customize a second lip to press against the side of the print bed as well so you have horizontal and vertical pressure on the build platform. Instructions Get openscad:...
thingiverse
I made this quick stand for my fake stained glass art. ...The art was created by coloring clear Elmers glue, and painting the glass with the mixture.
thingiverse
Created to hold my 200mm borosilicate glass on my 220mm heating bed for better flattness. ...Print Settings Printer: Flogertech Kossel Rafts: ...
thingiverse
Print Settings Printer: Any with a heated bed Rafts: Doesn't Matter Supports: Doesn't Matter Instructions 1) Clean the borosilicate glass with water and alcohol, and bake PEI, double stick tape, and glass at 110C if possible (avoid bubbles down the...
thingiverse
Clip for holding down 120mm diameter borosilicate glass bed on Monoprice Delta Mini printer. (Glass plate from https://www.amazon.com/gp/product/B07BNJLKMF ) The clips wrap around the edges of the existing aluminum bed and do not interfere with the...
cults3d
after you clean off the old adhesive from your borosilicate glass print bed of course... get some glue remover to help with this part... trust me... rolling your thumbs across the glue over and over for hours works too, but may incur blisters as a...
thingiverse
Customized version of https://www.thingiverse.com/thing:1808029 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1808029