custom switch pro controller 3d models
1313723 3d models found related to custom switch pro controller.cults3d
A lightweight and sturdy stand, fitting and leaving well attached the Original Nintendo Switch Pro controller. With opening for charging cable. Ready to print enjoy. :) A light and robust support, fitting and holding the Original Nintendo Switch Pro...
thingiverse
Made some adjustments to mrfochs Xbox controller mount to work better with a Switch Pro Controller. The original mrfochs file actually does happen to work with a pro controller as is, but holds it more by tension than proper fit. ...I'm hoping this can...
myminifactory
This allows you to attach your Switch to a Pro Controller allowing you to play on-the-go in, my opinion, the most comfortable way! ... It's a challenge for me to model pro controller as perfect as I want it to be, so the fitment isn't amazing, but it is...
thingiverse
This is a hard case for the switch pro controller. ... there is a pin for the front of the case, as for the hinge, i found some spare short wood screws and made it work.
thingiverse
Remix of the xbox one controller stand by Sethbon. ... https://www.thingiverse.com/thing:3280377 Swapped the xbox logo for the switch logo as its fits the controller nicely.
thingiverse
NO SUPPORTS! ... a lot of the pro controller stand I've seen are super bulky, and are hard to print. this one makes it super simple, and super fast to print. mine only took about an hour to print. ...and only 22 g of filament (print on its side)
thingiverse
simple, minimal stand for a switch pro controller.
thingiverse
Here's a solution to play an undocked Switch with a Pro Controller
thingiverse
First Thing i puplished. ... It is a Pro Controller holder for the Switch dock. ...
thingiverse
... own controller caps. Keep in mind you have to use flexible filament for it to work. I have splatoon 2 ones and a custom one, so you can add any logo on top. These only work on the Nintendo Switch Pro-controller. I will add more later. Enjoy! ...
thingiverse
Mount to hold the switch and the pro controller together. ...Updated with v5 adding a latch to help secure the mount to the controller.
thingiverse
NIntendo switch pro controller holder for the dock. made some minor changes. compared to the picture it is a bit lower. ... print with supports
thingiverse
A basic stand for either and Xbox One or Switch Pro controller. ...No supports needed if you print on its side.
cults3d
... your switch above your controller. ...Brings it closer to you while allowing use of the pro controller, and is nicely balanced. ...Carefully open up after printing in case any filament fused at the closure, and then snap around controller at the front.
thingiverse
... of its sides. ...Remix from @minifake 's Stadia controller holder: https://www.thingiverse.com/thing:4040750 I modified the original one to place the Switch pro controller in the same height and position that Stadia Controller in the original Thing.
thingiverse
... your switch above your controller. ...Brings it closer to you while allowing use of the pro controller, and is nicely balanced. ...Carefully open up after printing in case any filament fused at the closure, and then snap around controller at the front.
prusaprinters
This is a remix of https://www.printables.com/model/141662-nintendo-switch-pro-controller-dock-stand-with-gam/files , but I just sliced off the bottom of the model (that attached to the Switch dock) and instead made the base a little wider to hold...
thingiverse
This is a remix of the now standard switch pro controller mount that allows you to use the standard modular mounting system to mount whatever you'd like to your pro controller. I specifically designed it because I wanted to use my controller as a...
thingiverse
The Switch Pro Controller finally gets some love. Get more precise control in racing games. With non-analog triggers [gas & brakes] you need all the help you can get. What you need: 608 bearing, 22mm diameter, 7mm thick, 8mm center. ... ...
thingiverse
I really liked [araymbox's PS4 Wall Mount](https://www.thingiverse.com/thing:2545861 "araymbox's PS4 Wall Mount") and I wanted one for my Switch Pro Controller. I found [naten11's Switch Modular Wall Mount](https://www.thingiverse.com/thing:2906017...
thingiverse
# Functionality This currently only will fit with the Nintendo Switch Pro Controller (and any other 3rd party controllers that are the same size, I have not tested any) # Future Plans I plan to update this post eventually to support more controllers...
prusaprinters
At the time of uploading, there didnt seem to be any dedicated Switch Pro controller desk stands on here, so i thought I'd give making one a go. The legs of the controller are flush with the table and act as additional support, so the stand and...
thingiverse
I do not own the Nintendo Switch, Pro-Controller, Nintendo, or any affiliated franchises. This model was made for the intention of free use and edits. Please do not sell model files of controller parts. ...You can, however, sell replacement parts after...
prusaprinters
I really liked araymbox's PS4 Wall Mount and I wanted one for my Switch Pro Controller. I found naten11's Switch Modular Wall Mount which is really good, except I wanted it to match the PS4 controller clip I already had. So I mooshed the two designs...
thingiverse
Made to hold the Nintendo Switch Controller. Works alright in this revision but needs to be modified to provide more support in the back. ...Print Settings Printer Brand: Printrbot ...
thingiverse
This form-fits the first-party Nintendo brand Pro controller. I'm not sure how well it will work with third-party controllers. Depending on your printer settings, the logo insert (printed in a different color) may be a snap fit or require a drop...
thingiverse
I printed the original and it worked fine. ...I remixed it fixing the center of gravity, added hooks for a rubber band and made a opening to charge the switch. Update 6/24/18: can scratch your controller. ...I'll look into some type of padding
thingiverse
This is a scan of a pro controller right grip. This was scanned in using a Creaform GoScan!20 using their VXScan software. I was not able to get the innermost part of the cavity scanned in. I tried repairing the file using meshmixer, i will print one...