cx10 3d models

... work Change notes v1.0: First draft v1.1: Height of the box updated v1.2: Hinge reinforced. The box is not WIP anymore v1.3: Cut added in order to fit the new CX10 wifi antenna, cover unchanged

This is a replacement thumb-stick for the Cheerson CX10 mini quadcopter controller/transmitter. The dimensions are modelled on the Turnigy/FlySky i6 (same thing) and the idea is that, by replacing your stock thumb-sticks with these, you build more...

A friend only likes flying "pinch" style on the TX, so I made this stick replacement. Edit: I've added a second version that replaces the whole stick and base assembly. full_cheerson.stl requires the TX to be disassembled (a few screws), but might...

attach to top quadcopter with double stick tape

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/7mwS6gWs3F7 Non Tested.

Customized version of http://www.thingiverse.com/thing:1341482 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1341482 Instructions Using the following options:...

Case was designed so that I could safely carry my quad in a bag without it breaking or props bending. ... Lid snaps into the bottom securely.

Mod for the Cheerson CX10 & Hubsan Q4 mini quadcopters. The mod turns the mini quadcoptor in to a rolling RC Vehicle which looks like a sort of Star wars Tie Fight. Whether you have the CX10 or Q4 both models fly well with this mod added. The...

Just sticks extension, similar to "big" RC radios' sticks ;)

<p>Just sticks extension, similar to "big" RC radios' sticks ;)</p> Category: R/C Vehicles

This is a modification of the existing box designed for 1/4 inch magnets http://www.thingiverse.com/thing:769184 . Unfortunate for me, Hobby Lobby sells 1/4 inch magnets that are 8mm in diameter?!! I didn't even notice this until I had the lid...

The Atari 2600 was my first games machine and so the CX40 was my first joystick and it survived long enough to be used with my ZX Spectrum and C64. I loved that hunk of plastic but I knew even then that it wasn't the best joystick out there, so after...

The Atari 2600 was my first games machine and so the CX40 was my first joystick and it survived long enough to be used with my ZX Spectrum and C64. I loved that hunk of plastic but I knew even then that it wasn't the best joystick out there, so after...

prop guard for the cx10 please don`t complain i am far from an expert with solidworks :-))) Flying is much better without it ;-)

UPDATE June 5, 2015: Added models for Cheerson CX10 as requested Instructions Mine are sliced at 0.2mm layers, 0.48mm width. ... Clip to the bottom of your Q4 motors (careful of the wires!) or remove the props and fit them above the frame for a bit...

... rectangular battery case. ...Classic CX10 will also fit. I've also remixed one for a single CX10C / 10D. https://www.thingiverse.com/thing:2503056 Print with 0.8mm bottom/top layers and 0.8mm wall. 20% infill. ... For a total weight around 80g

Remixed from this great box https://www.thingiverse.com/thing:1390223 , for CX10C or CX10D that have a rectangular battery case rather than the square one of the classic CX10. The cover is to be found in the original *Thing* Print with 0.8mm...

I had a Cheerson CX10 some time ago and the same mod applies. I know there are already a ton of these, but I wanted to try doing something in OpenSCAD by myself. You should probably adjust the inner diameter of the smaller hole to get a tight fit,...

it uses 8 brushed coreless motors 12x6mm as CX10 motors. Will update soon with more infos! ...Print Settings Printer: Prusa i3 Pro B Rafts: ...

Because the new battery does not quite fit the CX10 housing I thought up this alternative. You might want to add glue because it still comes apart on rough landings. Tips: - Add a bit of plastic (cut from a blister package) between battery and...

SKYWLKR,SYMAX2,XINXUN,NIHUI) 5 9.KN(V977) 6 12.CX10(CX-10 blue,CX-10 green,DM007 on ER9X submenus) 7 13.BAYANG-(CG-023 on ER9X) 8 2.Hubsan 9 3.Frsky A 6.Dsm2(DSMX submenu on ER9X) B 7.Devo C 10.SymaX(Symax4/11/12/X5C)(submenu ER9X,SYMAX5C,SYMAX4) D...

thing:689333 modified so main guard is sturdier (2mm instead of 1) 4 pillars to allow top to be glued top piece to be glued on top of the pillars of the bottom guard This way it looks IMHO better and even if the cx10 drops on the head it will protect...

There's also a GitHub repository now: https://github.com/KP1533TM2/cx10-parts Print Settings Printer Brand: RepRap Printer: Migbot Prusa i3 Rafts: No Supports: Doesn't Matter Resolution: 0.08mm per layer, 1 perimeter-wide walls Infill: 100% inside...