cyma cm 127 3d models

Here is my first version of a "Kriss-Vector-Style" Front-Grip for the Cyma CM. 127 AEP. Maybe i will work on an updated version, to hold one spare-magazine in the frontgrip. This will only fit the Cyma. CM.127 AEP. It wont fit the CM 030 aka. ...Glock...

Rail mount for the Cyma cm.127 electric airsoft pistol

Hey, here ist an carbinekit to convert the Cyma CM.127 to an SMG. You also need threaded rod (M6). ... Have fun

Dies ist ein Prototyp welchen ich mit Hilfe eines Originalen Cyma CM 127 Magazin erstellt habe. Leider brauch mein 3D-Drucker noch etwas bis er geliefert wird weshalb ich Das Magazin noch nicht ausprobiert habe... Für denn zusammenbau werden noch...

A relatively compact way to run your Cyma CM.127 electric pistol on full size AEG batteries for faster trigger response, fire rate, and far longer battery life. Internal size 19x36x140mm, 9.6V Nihm brick shown in photos. ... Uses one m3x35mm bolt and...

This is an adapter designed for Cyma 127. ...You need a screw (M3 x 25mm) and a nut.

This is an adapter designed for Cyma 127. ...You need a screw (M3 x 25mm) and a nut.

Replaces the rail on a Cyma CM 702 airsoft sniper riffle to a picatinny rail. This enables the use of scopes with a smaller mount. You will need 4 new M3 screws that are a bit longer... ... Derived from: http://www.thingiverse.com/thing:452730 ...

---------------------------------------------------- Here is a rail that fits the Cyma CM.131 AEP. The rail is attached to the existing threads of the slide with the help of 2 screws (M4x6mm). At the front, the rail is held in position by the...

Here is carabine kit for cyma 127 electric pistol. Carabine kit is perfect for cqb games. On top , sides and down of carabine you got ris rails for attatchments like scopes , grips or lasers. Pistol got fire selector which gives you option to shoot...

You can use these to replace the standard plates on your CM.127 Phantom AEP. ... maybe scale them down a bit on the Z-Axis.

This is a fire selector cover for CM.127(S). It is intended to replace the original fire selector if you want to mechanically disable the full auto (or your field requires it). For airsoft use only! **Any thoughts and recommendations will be...

The trigger lever on my CM.030 broke when I was converting it to accept LiPo batteries. The original part is made of horrifyingly cheap metal. Over time with use a couple of fine splits had appeared that finally gave in when being carefully...

This is a Pouch Insert for Standard Magazine Pouches to fit two Cyma CM.125 USP Magazines. It is designed to sit very tight in the pouch. May fit other magazines as well, the slots are designed to be 9,8mm wide, my magazines have a width of 9,7mm. ... ...

You can spend 10 euros on an 14mm ccw Adapter for the cyma cm.126, however i decided to make one myself. It just replaces the original endcap and the slide can still be dissasembled to change the battery. ...Be carefull when trying to take of the endcap...

The same as my [M4 / AR15 STANAG Magazine Stand](https://www.thingiverse.com/thing:2669987) I wanted a little stand for the small magazines for my Cyma CM.030 AEP. I made a 1 through 3 mag version available seeing as that it's a sidearm you...

Finally - third iteration of my CM700 Mag project :) Spare mag holder for Cyma CM.700 in the form of M40A5 mag. Edit 11.2021 -There is version 2 with cuts to take out magazine even easier to reload You just need to take out pin and remove bottom...

... of a barrel. ...fixed it. "Working" Silencer for a Cyma Airsoft electric pistol. I made this to fit my 1911, and it should work with other Cyma pistols. ... Here is the original maker of the silencer: https://www.thingiverse.com/thing:3643816

Finally - third iteration of my CM700 Mag project :) Spare mag holder for Cyma CM.700 in the form of M40A5 mag. Edit 11.2021 -There is version 2 with cuts to take out magazine even easier to reload You just need to take out pin and remove bottom...

ON GOING PROJECT If you bought a M4 cyma cm515 like me, you've probably exprienced braking the sling plate just after some hours of using it. you can buy a new one in metal for like 6$ but i wondered if we can 3d print it. So i started to...

I wanted a railed upper handguard to match the ribbed CM-045 that I have, and atapiaco had already made a very nice low-profile rail, and I just added the ribs and a couple of screw holes.

This is a slector plate for a gearbox V2, it should work on any M4, but has been fine tuned specifically for the cyma cm 515, so if you have another one it might require some modifications. ... So i give the STL and STEP files so you can do whatever...

If you are making an R-Hop for your Cyma CM.030 (Glock 18C) and you would like to keep your original hopup arm intact, or if for whatever reason you would need a replacement part, this is the model you are looking for. Use first a 1.3 and then a 1.5...

If you are making an R-Hop for your Cyma CM.030 (Glock 18C) and you would like to keep your original hop up arm intact, or if for whatever reason you would need a replacement part, this is the model you are looking for. Use first a 1.3 and then a 1.5...

A slide on sheath to give the CM.126 a under barrel rail. You need to slide it off in order to get the battery in and out and it is a tight fit but does slide on and off. ... Not tested on the field yet but I've stuck a hefty light on it and thrown it...

A slide on sheath to give the CM.126 a under barrel rail. You need to slide it off in order to get the battery in and out and it is a tight fit but does slide on and off. ... Not tested on the field yet but I've stuck a hefty light on it and thrown...

I'll recommend to remove the hatch, since it swisgs freely when it's opened :) ( yes.. it's sitting inside with hot glue in the groove on top of this model and dropped into the dummy magwell hole... ...) Todo: - Make it bit shorter - Lock-in...

2 Slot Magazine Pouch Adapter for AEP Mags (Cyma CM.125)

kit feito para gearbox cyma cm 022 faça sua propria arma de airsoft. ...https://www.youtube.com/watch?v=cZtEnlBn6cQ&t=304s