d 9 connector 3d models
337265 3d models found related to d 9 connector.thingiverse
I found the pins would keep sliding back through the plastic, so instead I decided to switch to using 9-pin D-type connectors. This part attaches a connector just below the extruder so the entire hotend connection (bowden tube and electrical wiring)...
thingiverse
Cover for a solderless 9 pin D-Sub connector. (see photos) Prints in two halves, no support required. Finding the right size screw to mechanically join the two halves may be tricky! At the present time, unless the connector your fitting the assembled...
thingiverse
I'm using the custom extruder mount for my reprappro mendel to gain additional height. ...I had to modify the d-sub connector to fit on the new mount.
thingiverse
... kind regards, Andrew Instructions Used the standard dimensions of a D-sub connector in order to create a case for simple, but quick installation for cables and/or connectors around the 3D-Printer; Also for future computer/ electronic projects.
cults3d
The original housing looked already great, but I needed to create an adapter from female to male with a crossover pin-layout - so I removed the rear part of the original housing, mirrored the other half and put both together to get a double-sided...
thingiverse
The original housing looked already great, but I needed to create an adapter from female to male with a crossover pin-layout - so I removed the rear part of the original housing, mirrored the other half and put both together to get a double-sided...
grabcad
This is a model of a Norcomp 380, MICRO-D Series, 9-pin PCB D-sub Female Shell Connector with Male Pins on a 1.27mm pin pitch. This connector is typically used for low speed (< 1 MHz) data and control. ...Electrical limits are 500mA and up to 500...
grabcad
This is a model of a Norcomp 380, MICRO-D Series, 9-pin PCB D-sub Male Shell Connector with Female Socket Pins on h a 1.27mm pin pitch. This connector is typically used for low speed (< 1 MHz) data and control. ...Electrical limits are 500mA and up...
thingiverse
I needed a 9 pin VGA / D-sub type connector for a printer wiring loom i'm working on. I saw Gary Hodgsons http://www.thingiverse.com/thing:10456 which was nice - but too fragile and a bit clunky (because it needs vitamins.) This is a ground-up...
thingiverse
thinned the connector part to 1.2 mm so connectors from e.g. ...TRUComponents orr PhoenixContact would fit better. I use it to attach a SUB-D 9 pole connector with connection terminals to a front panel of a box
cults3d
A plug housing for Making your own Amiga RGB video cables by joining two d-sub 9 connectors together. Trim the connector tabs and inside shielding as shown in the photo and solder together while aligned in a male d-sub connector like the Amiga RGB...
cults3d
A simple connector for OSB boards. ... Work with thickness from 9 -16 mm. ... Needs screw M6 x 25mm and nut M6
thingiverse
A simple connector for OSB boards. ... Work with thickness from 9 -16 mm. ... Needs screw M6 x 25mm and nut M6
sketchfab
Rockart at Nämforsen, mid part of panel D:9. Experiments with mobile camera. ...Photo: Martin Model: Martin
thingiverse
D-D Jump guard piece if your aquarium is not square but you have 45gr corners instead of 90gr.
thingiverse
A simple D-15 connector cover Instructions Print, clean, put the connector in and close the cover using two M3 bolts and nuts.
thingiverse
This is a simple housing for 9 and 25 pin D-SUB connectors. Other sizes might follow. I needed such a housing for a current project and I couldn't find any I liked. Currently, the housing is strictly symmetrical. So you just need two identical...
prusaprinters
This is a Sub-D connector but with a bigger hole so you can add a bigger cable of cable proctection.
thingiverse
... You can use pins taken from other D-Sub family connectors like D-Sub 25 (which is cheap as beans on the other hand). Jus keep in mind that you probably would like to solder your wires before plugging in pins to avoid melting the plastic. ...Enjoy!