d and d dice set 3d models
2411394 3d models found related to d and d dice set.thingiverse
I designed this 7 part dice set for a friend to turn into a mold for resin casting. Would not recommend to print these for direct use since it would be hard to make them "fair". Also recommend to print on a resin printer or very small layer-height...
prusaprinters
I designed this 7 part dice set for a friend to turn into a mold for resin casting.Would not recommend to print these for direct use since it would be hard to make them "fair".Also recommend to print on a resin printer or very small layer-height to...
cults3d
A set of 7 bone dice for D&D. Scaled to the 15mm standard. The set includes 2 variants of each die, one solid and one hollow. A collection of 7 dice trays to hold a set of 7 dice and has an area for rolling. Designed to fit a 15mm Chessex set of...
cults3d
Dice set based on a special edition of metal made for d&d. ... D4, D6, D8, D10, D100, D12, D20 7 models .obj
cults3d
That thought lead to a full set of custom D&D dice in Klingon. The dice should be sized and scaled correctly and be ready to print. (preferably on a resin printer) Please keep in mind I haven't tested these yet so tinkering may be required. ...I also...
prusaprinters
As I could not find a good complete set of seven RPG dice, I scaled and collected the best dice I could.
thingiverse
As I could not find a good complete set of seven RPG dice, I scaled and collected the best dice I could.
cults3d
As I could not find a good complete set of seven RPG dice, I scaled and collected the best dice I could.
thingiverse
Blank dice set used to create a dice holder. ... Includes: - 1 d4 - 1 d6 - 1 d8 - 2 d10 - 1 d12 - 1 d20
cults3d
Coasters designed to be printed and painted. Set has a wireframe view of d20, d12, d10, d4. ...They are also available with extensive post processing available on my Etsy page here:...
cults3d
A set of 7 dice for D&D. Scaled to the 15mm standard. ... The set includes 2 variants of each die, one solid and one hollow.
myminifactory
1 Set of plane blank D&D Dice : D20, D12, D10, D100, D8, D6, D4 1 Blank Small Dice Tower 1 Blank Dice Dish 1 Black Dice box/Chest All you need to start D&D! or any other table top. ...:)
thingiverse
7 Piece dice set with D&D ampersand logo for highest roll. ... Please post your makes, let's see what these look like!
thingiverse
This is a pre supported set of dice masters, with a sprue. ... You can cut the sprue and use them as dice as well.
myminifactory
Supporting dice to print properly on a resin printer takes ages, so here's a set already pre-supported that I'm offering to the dice making community free to use. The font used is Source Code Pro from Google fonts and has an SIL Open font licence,
cults3d
A simple 6-piece dice set, including a D4, D6, D8, D10, D12 and a D20! ...WARNING: unless these dice are printed at a pretty high scale, they are better suited for a resin 3D printer, as most of them have really fine detail in the indented numbers
myminifactory
My best settings are listed below, however these were just used to get the best possible dice, and the brim is the only setting that I would say is required to get a correct print. If you would like to make the numbers a different color, use both...
thingiverse
My best settings are listed below, however these were just used to get the best possible dice, and the brim is the only setting that I would say is required to get a correct print. If you would like to make the numbers a different color, use both...
thingiverse
ENG: I designed this dice and mini box for D&D or any similar game, its meant to hold all your standard dice set and some extra ones as well as your minifigure and a small pen or pencil. I leave the .f3m fille in case you need to edit it. ESP:...
thingiverse
Built a simple travel container for my D&D mini and dice. Space for the mini's is 26x40mm. The mini in the pictures is 36mm tall and has a 24mm base. This will hold standard 16mm dice. The design is symmetrical so you can hold up to 2 minis and 8...
thingiverse
... I know that it might take some experimentation to get the threads to print properly. That's why I've included a part which is just the threaded part of the cup. The lid is the D&D logo and the cup was my attempt at creating a dungeon wall. ...
thingiverse
It has a removable box inside so you can take the dice out and use the hollow center for a dice tray. The removable box has a drawer that will hold 8 dice. The Box and the drawer is held together by 5mm cube magnets I got on amazon. The holes for the...
thingiverse
Print two of the vaults and you can store 3 sets of dice as well as a mini. The magnets I acquired to fit those holes are more than strong enough to hold all of this, even with metal dice and a large mini. I designed this using Tinkercad with the...
prusaprinters
Print two of the vaults and you can store 3 sets of dice as well as a mini. The magnets I acquired to fit those holes are more than strong enough to hold all of this, even with metal dice and a large mini. I designed this using Tinkercad with the...
thingiverse
... ...The vault has two grooves just long enough for one set of dice each and a slot big enough for a 28 mm miniature with room to spare. ...Instead of making said slot wider to fit more minis, I decided to make a slot acting as a phone stand instead.
thingiverse
Holds 2+ sets of dice (I was able to fit in 2 complete sets and a few extra D8s) or 1 set and a few pencils. As well as room for a miniature, a deck of spell cards, and a storage area for the spell tracker tokens and other miscellaneous tokens. ... Top...
youmagine
A simple, elegant way to carry around your dice and roll in style in your games.
thingiverse
I've made the holes 3.2mm deep and added a tiny 65-degree chamfer which makes it easier to set in. I didn't notice but apparently, someone else beat me to putting up a design [here on thingiverse](https://www.thingiverse.com/thing:3575125) but I...
prusaprinters
My changes:-Revised inside to include specific coin storage area.-Added D&D logo to the top of the lid-Revised the coins and spell slot tracker, coins and slots were made smaller as to fit inside the box. Also added the D&D logo...
pinshape
This is a Dice box and Mini Holder in 1! Printed with the following settings: - Layer Height: .2 - Wall Count: 4 - Top layers: 5 -Infill: 10-25%, depending on material/ strength desired -Support: Yes ( I use CURA's tree supports for this, it seems...