d sun usb to ttl 3d models
2154824 3d models found related to d sun usb to ttl.thingiverse
This is a case for the D-SUN USB to TTL converter sold by Banggood and other places. There is a hole in the bottom so you can see what each pin does. Print Settings Printer: Flashforge Creator Pro 2016 ...
thingiverse
Case for USB to TTL Converter. ... U need: - FT232RL FTDI Mini USB naar TTL Seriële UART Adapter - 15 x 10 mm Boot Rocker Switch - 3 mm led - 150 Ohm resistor - Some wire Use Dupont or Pogo Pins
thingiverse
Here a tiny case for a USB to TTL (FTDI) adapter. ... The case version 11 is equipped with a mounting rail for Anycubic Vyper!
thingiverse
CP2102 case TTL to USB, for a friend. ... this is a remix of https://www.thingiverse.com/thing:2580443
thingiverse
Cover for CP2102 USB to TTL. ...The device is maked by SILABS.
prusaprinters
Simple case for FTDI FT232 USB to TTL Serial converter module. ...For simpler usage, it contains also description of pinout and output level switch.</p><p>Designed in OpenSCAD.</p><p> </p><p>Printed on Alfawise EX8 with Alfawise PLA, which explains...
myminifactory
Small and neat case / enclosure for USB to TTL adapter: http://got.by/3mso9k (USB to UART: RX-TX for Arduino Pro Mini and other boards with COM port) Works fine, protects the board from accidental shortcuts. ... No screws, just a lock to hold the cover...
thingiverse
... the openings is lower for the usb side. top should be obvious. check picture of the board I have to see if you have the same type before printing, it's one of the most common cheap ones I printed mine in PLA at 0.20mm layer height no screws needed
thingiverse
After printing out https://www.thingiverse.com/thing:1557552, I noticed that my CP2102 programmer from the same source wouldn't quite fit due to manufacturing differences. Also, I had no M2 screws lying around. So I set about creating my own from...
thingiverse
This is a housing for the Nextion "Nextion Foca Max 5V2A Output USB To TTL Serial Converter Board" --> https://itead.cc/product/nextion-foca-max-5v2a-output-usb-to-ttl-serial-converter-board/
grabcad
FT232RL 3.3V or 5.5V FTDI USB to TTL Serial Adapter Arduino STM32 Mini PortRed board
thingiverse
This is a case for FTDI USB To TTL Serial Converter like this one:http://www.banggood.com/fr/FT232RL-FTDI-USB-To-TTL-Serial-Converter-Adapter-Module-For-Arduino-p-917226.html Print Settings Rafts: No Supports: No Infill: 20
thingiverse
This is a case for the USB to TTL converter (type HW-597 or similar models), used to make a programming cable for a Baofeng (UV-5R) or similare portabel radio's. You have to cut a small piece to the plastic , see pictures. ... You need a some glue for...
thingiverse
USB to TTL twin-tower for CP2102 breakout Platine 15.5 x 20.5 mm Ein schickes und praktisches CP2102 Tower oder Twin-Case. Es kann auch als Einzel-Kasten benutzt werden zum Schutz der Platine. Jeweils 2 Versionen mit und ohne 0.2 mm Schicht. ... Die...
thingiverse
Small and neat case / enclosure for USB to TTL (Serial Port) adapter: http://got.by/3mso9k (USB to UART: RX-TX for Arduino Pro Mini and other boards with COM port) Works fine, protects the board from accidental shortcuts. No screws, just a lock to...
thingiverse
Other than the "USB To RS232 TTL CP2102 5Pin" module you need two 10/12mm M3 bolts and two M3 nuts. As i said this enclosure is not meant for prototyping but for production time. So you need to solder permanently your cable with the pins in the...
thingiverse
It is also compatible with a TTL to USB adaptor of the same size. The box have cable retention. This is why I made it, instead of just using shrink flex. I have used it to make a TSDZ2 programming cable, which is need if you what to change the...
prusaprinters
This box encapsulate the ST-LINK V2 mini, if you have soldered cables to it on both ends.It is also compatible with a TTL to USB adaptor of the same size.The box have cable retention. ...This is why I made it, instead of just using shrink flex.I have...
thingiverse
... using micro-usb for power only when you can have the full interface? ... With a ch340e breakout like this one: https://www.aliexpress.com/item/33041987984.html You will have to glue it in, and some keys are provided to grip the glue behind the board.
thingiverse
Wiring diagram and PCB on [EasyEDA](https://easyeda.com/editor#id=4b2579163474468580118d101a0473d5|27c1c9f704fd42adaf81fc77c32b0d07) ##BOM * CP2102 USB 2.0 to TTL UART Module 6Pin Serial Converter * RJ45 PCB socket ##Another my version * Micro USB...
prusaprinters
EQ direct USB adapter for Sky-Watcher EQ6 Pro, HEQ5 and similar mount. Wiring diagram and PCB on EasyEDA BOM CP2102 USB 2.0 to TTL UART Module 6Pin Serial Converter or CH340G USB TTL Converter Adapter STC Brush Module RJ45 PCB socket Another my...
thingiverse
... mounting holes, but the USB-TTL board doesn't. It is also the most likely board to be yanked when someone accidentally trips on or tugs the USB cable. ...This box allows you to mount the board to your machine with a bit more mechanical soundness.
thingiverse
Просто міцна коробка. Отвори під світлодіоди не робив, бо друкував білим пластиком, а через нього й так добре просвічує. Якщо ваш пластик не прозорий - дрель вам на допомогу. ...
thingiverse
The outer dimensions are the same as the original, but there ia more space for the Geekcreit® PL2303 USB-TTL, also sold by Banggood.
thingiverse
He diseñado una cajita para un conversor USB-TTL que compre en Ebay para programar los arduinos u otra cosa. Se que quedaria mejor con las esquinas redondeadas pero no lo pense al imprimirla. EDITADO: He subido el STL con las esquinas...
thingiverse
It is a USB case that we can fix like a tower. ... It is ideal for plug with a extension cable usb.