da vinci pro 3 in 1 review 3d models

See the video for more details:https://youtu.be/jrzTfVF7P9E Print Settings Printer: Da Vinci 1.0 Pro Supports: Yes Resolution: 0.2 Infill: 20% Notes: Make sure to print 1 backplate and 2x exhaust fanduct double version 3. You can print them all...

With this rack, that you mount on the carriage of your Da Vinci Pro printer, you can add 2 exhaust fans so that they cool your print by blowing air over your print. Now you can print much larger bridges and overhanging parts with your printer then...

I made this specifically for my da Vinci Pro 3-in-1 printer and thus it fits nicely for that printer. Feel free to adjust the design for your printer type if needed. As a little side note I added text above the filament entry which reads: "Speak...

Links oder Rechts zu verwenden

turns out with the upgrade you'll have to buy a ramps 1.4 board kit because the da vinci board is different from all other 3d printer's control board that the repitier firmware ( 0.91 and 0.92 ) that are now out were nearly a complete redesign of...

The in-feed for the XYZprinting da vinci 1.0 pro is not exactly optimal, as it will quickly get worn when using third party filaments, because of the angle at which the filament is fed. With this I wanted to replace the small clip, and use a...

Knobs for da Vinci 1.0 Pro. You have to print two pcs for rear and one for front. Knobs fits perfect. Just "click" it. PET-G is the best material for this model. ... PLA and ABS will crack.

Designed from my Da Vinci Pro when I was disassembling it. I saw some guys cutting the original one to make some mod and that hurt me... lol... ...You can use it to do whatever modification you want.

22 November 2017 This is a complete replacement of the Bowden Extruder for the XYZprinting Da Vinci 1.0 Pro printer with the exception of the Stepper Motor which is retained in its entirety. Over time the original extruder weakened. The idler pulley...

... at least 2 locations. (A, B) With this small amendment, I am able to correctly level the table. Sorry for my English. I tried to use google translator. Print Settings Printer: Da Vinci 1.0 Pro Rafts: No Supports: No Resolution: 0.2 Infill: 100%

I created this S3D profile for the XYZ Da Vinci 1.0 Pro, when the machine was not supported by S3D. It has become redundant as the machine is now fully supported by the latest versions of S3D. Also note that I replaced the hardware in my printer...

Printed in 0,2mm resolution with supports, as shown on the photo. Easy mount and removal. ... Little things DO MATTER :)

This is a somewhat hacked-up re-mix of the body of bdwalker1's "XYZ da Vinci 1.0 Pro E3D V6 Drop-In Cartridge Mount" to make it hopefully cool the E3D hotend better. I closed some gaps that let cooling air escape where it shouldn't, opened up the...

Use promo code TYFALL2019 Tindie store: This thing makes it easier to install an E3D V6 hot end in a XYZ da Vinci 1.0 Pro printer by merely unclamping/unplugging the stock extruder module, transferring the PCB and fan from the stock extruder...

Please consider a small [donation](http://paypal.me/geoffsim59 "PayPal") if you find this design useful. Drop-in E3D Mount for modified DavInci Printers. This will not work with stock printer hardware/firmware, as there is no provision for the...

After printing the original Drop in cardridge my E3d v6 wasn't lined up with the origanal PCB. for this reason i modified the mounting of the heat sink by 1mm. this version is printable whitout supports This thing was made with Tinkercad.

I modified the Da Vinci 1.0 Fan Mount by LeoDuhVinci to incorporate the 120mm. Some of the airflow is blocked which I might try to improve on in later models. I then used 20mm to 100mm vent duct mounts by ffcp01 to create a extractor tube out of...

Da Vinci Pro 1.0 80mm spool holder. ... For larger filament spools

1.0 Pro 3D-Ducker in Verbindung mit einem 45 mm Radiallüfter. Ich nutze einen Radiallüfter Sunon GB1245PKVX-8 (45x45x20 mm). Filament cooler for better print results. Fits for da Vinci Jr. 1.0 Pro 3D-Printer with a 45mm radial fan. ...I use a radial...

... fans from both sides push the air from outside to inside. Also I have changed fans to 60x60x13 mm 12V DC 0,36A. I also added ChatToBrian's project of Exhaust Fan Duct for the XYZPrinting Da Vinci Pro 1.0 & 3-in-1. The result is amazing. ...

... angle the filament went in from other spoolholders I designed this one. ...Printed it and used it with 1 kg spools. Print Settings Printer: Da Vinci 1.0 PRO Rafts: No Supports: No Resolution: 0,2 mm Infill: 25% Notes: I used ABS it seems strong enough.

You can also add 4 LEDs in the holes at the bottom to light up your prints. I was feeling fancy so I also added some NeoPixel lights on the angled part at the top behind the fans as temperature indicators. ... Extra parts (required): -LM8UU linear...

Please consider a small [donation](http://paypal.me/geoffsim59 "PayPal") if you find this design useful. When I replaced the electronics inside my Da Vinci 1.0 pro, I designed this bracket to mount an MKS 1.4 and a Raspberry Pi 3. The mount is simple...

Simple Exhaust Fan Duct Adapter for Da Vinci 1.0 Pro, no screwing, just print and mount. If needed, use double side tape. Printed with supports in 0,2 layer hight. You must buy: 2x Brushless fans, type 4010s, 5v 2 wires.

... https://www.thingiverse.com/thing:1328848 Those PCB boards are different and dimensions are not the same. For the best results you should also use my front cooling system for E3DV6 da Vinci 1.0 Pro. ...https://www.thingiverse.com/thing:2722162

Designed for changing to a e3d v6 specifically for a Da Vinci Jr 1.0a Pro. The holes for the pcb and hot end mount were taken from the old Da Vinci hot end. I have only had my printer for a month and am still very new to it, but the best thing I...

Holds a 3rd party spool of filament onto the back of the Da Vinci Pro 1.0. The key is that you can still open the top cover 80% of the way to change filaments. ... I've seen other designed that prevent you from getting the cover open without snapping...

Da Vinci 1.0 Pro Side filament holder system for XXXL 2.5kg spools. Can be mounted onto left or right side. The Tube limiter is to prevent the tube to stuck between the top door and the housing. Double sided tape is used to fix small holders to the...

Da Vinci 1.0 Pro Tube Guide for rail https://www.thingiverse.com/thing:1689123 YOU NEED TO ADJUST SCALING FOR THIS GUIDE TO MATCH THE RAIL CHAIN!!!!! ... (my chains are upscaled to 117.6% of original from the link above) Little things DO MATTER :)

This is a prototype of filament guide for my XYZ Da Vinci 1.0 Pro which enables printing flexible filaments such as Filaflex 82A. It is designed to be inserted between the extruder plastic body and the filament sensor PCB without further...