dan a4 3d models
15005 3d models found related to dan a4.thingiverse
**Latest Version Posted Here: http://www.thingiverse.com/thing:3763705** This is a custom PSU bracket designed to raise the Dan A4 V4 PSU mounting points up about 5mm. This provides additional room for the cabling with use with a 92mm AIO (such as...
thingiverse
UPDATE: Now compatible with the new Dan A4 V4.1 3M PCI-E Riser This is the final versions of the Dan A4 (V4) Ultimate Cooling Kit. ...The following STL files are included along with their print settings: * PSU Bracket: 0.15 Layer Height, 100% Infill,...
thingiverse
Collection of parts for customizing your Dan A4-SFX. Door clips replace existing clips and provide vertical support to ensure the door does not sag/move. Cable combs are used to properly route 24-pin/8-pin motherboard power cables as well as two...
thingiverse
GPU spacer for the DAN A4-SFX case to fit some thicker GPUs like the MSI GeForce GTX 1080 Ti Gaming X 11G V1 has to be glued to the sidepanel V2 with door clips for the Lian Li pins V3 better mounting mechanism V4 (planned) will probably be with some...
thingiverse
... spacer is 17mm thick and combined with DEEPCOOL RGB 200PRO connected to the motherboard for LED light color control. Revision 1. 2020-11-26 v4-dan-a4-spacer-17mm_LED_part1_R1_with_holes.STL v4-dan-a4-spacer-17mm_LED_part2_R1_with_holes.STL
thingiverse
... of Dan Case is moving the motherboard up so this will likely not fit the v4/USB-c version coming out in 2019. https://www.amazon.com/gp/product/B07DXRNYNX/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 Dan A4 https://www.dan-cases.com/dana4.php
cults3d
In my case i have a Dan A4-SFX case and use a 13 " second monitor. for additional room on my desk i designed this Monitor Arm it works very well and it is easy to print. Depending on your needs, the middle connector can be printed in long or short.
thingiverse
(https://www.reddit.com/r/sffpc/comments/eqa3js/dan_a4_ultimate_cooling_kit_losercard_mod/) This is *not* a final product, as it has not been test fitted or even printed. It uses the same spacer clips from entrhopi's V3 design. The original file...
thingiverse
This is a modification for the DAN A4-SFX computer case. It's used so that you can replace the USB 3.0 Type A connector with a USB 3.1 Gen 2 Type C connector. I used the Lian-Li PW-IC01NH45 cable (http://bit.ly/2fvjwCV). I had to modify the cable by...
grabcad
Sfx form factor computer case about 7.2l volume.Model contains: 2,5" drive bay; 3M PCie x16 gen4 riser cable; 120mm AIO mounting bracket; front UBS Type C connector.Spring (at pushbutton) modelled with equation curve to flatten ends.Screws,...
thingiverse
Small Stand for the DAN Case A4. Improved thermals for your Case. I have two bottom FANs as Intake and this improves the Airflow. ...Gain additional 3°C.
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
User 'TheEngineer from builds.gg gave me the idea to drill a hole into the dan case, as the tabs don't seem to hold up when printed in PLA. Eventually, I want to make further revisions to this file in order to see if I can get it machined or...
thingiverse
If you've an AIO in the Dan Case A4 this support holds a 92x14mm fan in place. My mainboard is the Gigabyte B550I AORUS PRO AX and the placing fits for the front M2-Slot. Temperatur drops around 7-10°C. ... Only drawback is a bit turbulence noise...
thingiverse
17-12-2021: new version with a simplifie design and a reduced height 15-12-2021:I was looking forward to gain some space on my desk , so I imagine a vertical stand for my Dan Case A4. It is a first rough version that is working but that I will try...
thingiverse
This Fan Duct is designed for a 92mm Fan. ...Because of the height, it is fitting perfectly in the DAN A4 Case using a Noctua NH-L9i Cooler.
thingiverse
Bracket for a 60x60x10 / 15 mm fan above the power supply for the DAN A4 SFX 02.2021 (new version with holes) Does not fit, turn the power supply ;) I would be happy to receive feedback
thingiverse
With this you can use 2.5+ slot graphics card print the PCIe mover/holder with PETG or ABS. PLA might deform when the PC is heated up. ...
thingiverse
Needed a carry handle for my PC case and this was exactly what I wanted. Just need to change the holes to fit an m3 20 screw. I overdid it on the settings because if this fails it could destroy my PC. PRINTER BEWARE! I do NOT guarantee this...
thingiverse
Needed a carry handle for my PC case and this was exactly what I wanted. ...Just need to change the holes to fit an m3 20 screw.
thingiverse
I have designed little compliant inserts that allow you to repurpose the 120mm AIO bracket in the DAN A4-SFX to mount a 3.5" HDD if you have a short GPU. The compliant legs slot into the slots on the AIO bracket and provide a hole to screw a 3.5" HDD...
prusaprinters
These are the front parts of my Dan A4 SFX +16mm spacer (V4+) modified to take a slot for 2x USB type A connections and a blank area for an LED or maybe audio, or a button, up to you.The USB cable that I'm using is this one:...
thingiverse
# HEADS UP, I WILL BE TAKING MY MODELS DOWN SOON, THANKS TO THINGIVERSE TOMFOOLERY MESSING WITH LINKS, ETC These are the front parts of my Dan A4 SFX +16mm spacer (V4+) modified to take a slot for 2x USB type A connections and a blank area for an LED...
thingiverse
Top mount bracket for an 80x10mm fan to go into a Dan Case A4 v3. Friction mounts to the case frame. I am using an Akasa Slimfan 80mm x 10mm PWM Fan (AK-FN076). I had lots of issues with the fan rubbing the riser cable when using the fan as an...
thingiverse
I wanted the front cover to be ventilated. For the GPU cover, I wanted to add more ventilation towards the bottom for the 4080 FE. I had to modify the original clip because it was larger and intended for a spacer adapter. ****** The GPU panel...
thingiverse
Update 1: Added 5mm and 8mm feet These feet are made to rise the case from the surface with 3/5/8mm. In case there is a bottom mounted fan, this could increase airflow. ...