dart board mount 3d models

... For guidance, consult the MakerBot wiki (http://wiki.makerbot.com/relay-mount-kit). Assemble the mount by inserting 1/4" standoffs, stepper controller boards, 1" standoffs, relay board mounts, and nuts using M3 screws in specified lengths.

Mounting holes are slightly undersized (2.5mm) to allow board attachment without backing 5.5mm hex nuts; however, hex nuts should be used since holes are not threaded and the PCB will eventually loosen. Posts on mount are tall enough to run wires...

... small board 25mm x 25.4mm and needed some board clamps that didn't go under the board (reverse of what ships with the LumenPnP). ... So I made these for grabbing on to small boards.M3 through holes mounts on 30mm centers.8.5mm height above built plate.

After reviewing a few different Peg Board Mounts, I decided to make a more robust mount that would have more positive contact with the peg board. I have included 3 different parts: corner, edge and rear support. The design is around Peg Board...

Clear up your counter with this wall mount for your favorite cutting board. All you need is a few pieces of double sided sticky tape (Nano Tape, Gorilla Mounting Tape, etc). ... Attached you'll find 2 designs, 1 to fit a 3/4" thick board, and one for a...

This mount easy to print mount is for the most common expermental boards.https://amzn.to/3SspSWCInstructionsMount frame using #4 screws. Mount PCB using 4 screws. ...M2 for the small and M2.5 for the larger PCB

Pedal board mount for Boss effect pedals. Screw your pedals directly to your pedal board. No messing around with velcro. ... Any screws with a shaft thickness of 4mm or smaller should fit.

I just needed a stand off to mount an XL4015 circuit board, glued to a metal case. ... This fits this style circuit board: https://www.amazon.com/gp/product/B079N9BFZC

This is a Wall/Desk mount i have designed to fit most power boards The mesurements of recomended boards are: 50cm Wide 30cm Tall And it is to fit 5cm wide screws

It has three mounting holes, an area for the FreeLSS board to click into, and a mount area for the relay board with raised mounting holes. The mounting holes use m3 style screws for the mount and for the relay board. freelssMount_screwholes.stl -...

A convenient snap-on mount is available for Mendel's electronics, enabling you to securely attach your boards on the side, preventing obstruction in reaching the carriage.

Mount for Ironing Board for the wall, Use two wood screws to fasten this piece to a stud in your wall

I modified the back plate from https://www.thingiverse.com/thing:4227574 to include a mount for the Duet tool board.

This mount is used to hold an ironing board. ...For strength, I printed with 35% infill and rotated so the long edge is vertical.

The girlfriend demanded a mount for the ironing board to securely fasten it against the wall, and this is the final product she's been craving.

Mount Your Breakout Board with Ease: A Step-by-Step Guide for a 5 Axis MACH3 CNC Interface Breakout Board For Stepper Motor Control Instructions: Printed on PLA at 220°C and 60°C bed temperature, I found myself in a predicament when I couldn't locate...

You will need a simple case mount for your Fantin SD Board, which unfortunately does not come with any pre-drilled mounting holes. Post-Printing After printing, tap a thread into the 3mm hole (my printer always prints holes about 0.2mm smaller,...

This is a 26mm board mount designed specifically for users of Thingiverse and compatible with the model found at https://www.thingiverse.com/thing:3277826. ...The design features a mounting system that securely attaches to a standard 26mm board,...

I mounted a bespoke BYEBYE board designed by Peter Stoneham onto my Rigidbot printer frame using an entirely home-made solution. I had previously created the board's enclosure in ABS material, incorporating 100% infill density for enhanced stability,...

Here is a simple, quick to print mount for the buyapi.ca 4 relay board. I needed something for mounting a board on the wall. It's friction fit. ... https://www.buyapi.ca/product/4-channel-relay-module-for-arduino-raspberry-pi-5v/

The advantage of this design is that you only need to use two screws to secure the mount and circuit board, making it quick and easy to assemble. Removing the board requires just one screw, adding to its convenience. This design is fully...

This is a snap-in board mount designed for mounting circuit boards. The STL is specifically created for an Arduino Uno board. Due to its complexity, this design will not scale easily. To accommodate other boards, I have included a link to the...

A versatile fan mount for the Asus Tinker Board, this design forces its legs into the PCB's standoff holes, providing a secure fit. The added length of the legs raises the board by a few millimeters, allowing for improved airflow and heat...

It features two screw tabs that securely fasten the mount to any board, while the Pi itself fits snugly into place with a simple push fit. To ensure a perfect fit, you may need to adjust the scale up or down depending on your printer's calibration...

This versatile peg board mount made its debut at #mrrf2018 and was originally engineered to pair seamlessly with a peg board arm to support hot wheels track. With its adaptable design, it can be utilized for various purposes as long as the model is...

Urgency is a recent adaptation of the ancient Royal Game of Ur produced by Alex Coburn on Kickstarter (https://www.alexcoburn.com) Since the hardwood board is beautiful I wanted to make a wall mount for display. Mount is structured to support the...

This is a simple mount for the Dinsfire LIT board. This board gives lights to DDR machines that are hooked up to a PC. The tolerances of my printer made this a snap fit onto the pegs. ...Hopefully it will fit nicely for you too.

Mounting Plate for the High-Performance Falcon F16V2/F4V2 Differential Receiver Boards. ...Securely fasten the board with M3 nuts, precision-engineered standoffs, and high-torque screws, while utilizing strong 3M adhesive-backed tapes to firmly attach...

Thermocouple board mounting kit allows an Ultimaker TC1 board to be attached atop the extruder platform of a RoStock MAX V2. The boards are fitted to my revised dual extruder platform (http://www.thingiverse.com/thing:707701), however, the hole...

This is a corner mount for 6 mm thick foam board which can be adhered into a flat surface with double side tape or sealant. A wedge is used to hold foam board in place and can be removed when necessary. ...