dart case 3d models
207973 3d models found related to dart case.myminifactory
This Dart Case was influenced by https://www.myminifactory.com/object/3d-print-tom-s-protective-darts-case-91932 The Lid is held in place with a toggle, latched with a piece of 1.75 TPE. This case fits steel tip darts from 140mm to 155mm in length...
thingiverse
This Dart Case was influenced by https://www.thingiverse.com/thing:3314601 The Lid is held in place with a toggle, latched with a piece of 1.75 TPE. ... This case fits steel tip darts from 140mm to 155mm in length and up to 7.25 mm in Diameter and up to...
cults3d
This Dart Case was influenced by https://www.thingiverse.com/thing:3314601 The Lid is held in place with a toggle, latched with a piece of 1.75 TPE. ... This case fits steel tip darts from 140mm to 155mm in length and up to 7.25 mm in Diameter and up to...
thingiverse
Dart case based off of https://www.thingiverse.com/thing:3314601 Widened the flight slots and point hole. Also chamfered a few key areas. Fits ~155mm darts, likely need to use the rubber band attachment. ... if you need longer or shorter you should be...
thingiverse
This is a simple and compact dart case that I made for a friend. The end caps need redesigned but the functionality is simple. Price TWO of them and they will clip into each other and hold each other.... Admittidly, not the best design but I wanted...
thingiverse
This is a case for my darts. There is room for replacement tips in the front part. It was printed in two parts. The parts are connected with a 1.5 mm thick wire. Furthermore, two magnets(size: 12.4x2.4x5 mm) are needed for the closure. ... Finally,...
thingiverse
A holder for darts! ...pretty self explanatory. I printed at 0.3mm in PLA with no support, standing on end with the end that you put the darts in from on the build plate.
thingiverse
Diameter 0.9 mm long shafts up to 49mm additional cap for better protection while traveling extra groove for rubber bands CaseV1 for Darts up to ~157mm length CaseV2 for Darts up to ~175mm length (longer flight section for flightprotectors) both fits...
thingiverse
Just a container for your darts. I like this style because you don't have to constantly put the flights on and off which adds wear and tear to them. ... The wear allows the flights to fall out more easily.
thingiverse
It fits for most dart sizes but you can check the dimensions in the picture. You can print the body without support. Make sure, you print the lid on the side, although it looks a litle weired. ...The clamps will break at the layers if you print it with...
grabcad
http://b2b.partcommunity.com/community/partcloud/index?route=part&name=Dart+case+-+DOLLAR&model_id=61131
thingiverse
Custom designed, more info and download here: https://b2b.partcommunity.com/community/partcloud/index?route=part&name=Dart+case+-+PIRAMIDA&model_id=61127
thingiverse
More info and download here: https://b2b.partcommunity.com/community/partcloud/index?route=part&name=Dart+case+cover+-+DOLLAR&model_id=61133
grabcad
Custom designed, more info and download here:https://b2b.partcommunity.com/community/partcloud/index?route=part&name=Dart+case+-+PIRAMIDA&model_id=61127
thingiverse
I would like to share with you a Basler Dart camera case with the possibility of attaching to a photographic tripod. ... I use with daA1920-160um
thingiverse
Remixed from Carasibana Dart Case. I added pockets to the case and top so magnets can be placed. I printed the case upright with a raft and the top with the opening up and a brim. I used Tinkercad to add the pockets. The magnets I used are from...
cults3d
I wanted a more compact dart case that would -allow storing darts without disassembling -store some extra parts -be easy to use -extremely durable -be heat resistant, in car and such -fit better in back pocket -print cleanly Case is in two pieces,...
thingiverse
This is a steel dart case, although, it could be used for soft tip darts as well. 4mm W x 30mm D recess so the tips don't bottom out. 10mm W x 100mm D recess for most any competition size barrel (and shaft). 45mm H x 45mm D slots for the...
thingiverse
Premium Dart Case Designed to hold 3 darts Tapered Sides to make it easy to put in your pocket. Spare Tip Storage in Bottom Sliding Top Body ver 4 added 6/2/16 for bigger flights. Print Settings Printer Brand: MakerGear ...
grabcad
... photos! More info: http://b2b.partcommunity.com/community/partcloud/index#!part?name=Dart+case+for+smaller+darts+2&model_id=22979 http://b2b.partcommunity.com/community/partcloud/index#!part?name=Dart+Case+for+smaler+darts&model_id=22937
thingiverse
... ARE real photos! More info:http://b2b.partcommunity.com/community/partcloud/index#!part?name=Dart+case+for+smaller+darts+2&model_id=22979 http://b2b.partcommunity.com/community/partcloud/index#!part?name=Dart+Case+for+smaler+darts&model_id=22937
thingiverse
Custom designed, more info and download here: https://b2b.partcommunity.com/community/partcloud/index?route=part&name=Dart+case+cover+-+PIRAMIDA&model_id=61129
grabcad
Custom designed, more info and download here:https://b2b.partcommunity.com/community/partcloud/index?route=part&name=Dart+case+cover+-+PIRAMIDA&model_id=61129
thingiverse
Funda para dardos, con compartimento (con tapa) para dos cañas de repuesto o puntas de repuesto. ...Necesaria una goma para que no se salgan los dardos
thingiverse
Remixed "Dart Case - created in PARTsolutions by Dape", to support Larger 10mm Grips. The case is a bit longer as well to accommodate longer darts. 0.2mm Layers, w/ Raft. ...
thingiverse
My sketches are meant to be printed with one case for 4 sets of barrels plus one case for 2 sets of barrels and two lids. You combine the two cases together and fit them with the lids on top and bottom. ...Then you secure them with a rubber band for...