dash ipad mount 3d models
349900 3d models found related to dash ipad mount.thingiverse
I used to sit my iPad mini in the pull out tray in the center below the dash and use it as a dedicated GPS on long road trips, but I got tired of it sliding around and being so low in my field of view, so I remixed the excellent iPad mini holder by...
thingiverse
This is an alternative to another iPad mini mount that I created for my fan attack Clubsport VE2.5 wheelbase. This one mounts to the side instead of on top. It can also be printed in one piece. It will simply mount using the existing bolts on the...
thingiverse
... it on smaller size printer beds. ...So you will have to glue part one to the back of part two before mounting it on your Clubsport wheelbase. This bracket will hold A standard iPad mini in landscape format allowing for data port access on either side.
thingiverse
A set of two (left and right) mounting corners to suit an iPad Pro (9.7") in a smart-case. The rear surface curvature was modelled to suit a Toyota Landcruiser Prado 120. ... Attached using 3M VHB double-sided adhesive tape - clean bonded surfaces well...
thingiverse
Simple dash stand for iPad or iPhone with otter Box. Design for holding a iPad in our work truck to use Google maps. Just put two way tape on the bottom and it should keep your iPad with Otter box in place. ...
thingiverse
This project requires some creativity to mount to dash and put the charger in the one side. I had to glue the halves together and drill a hole through the printed piece and use epoxy to secure the charge cord, which is an adapter to have an aux...
thingiverse
Just needed something to hold a magsafe charger in my car, I drilled this into a hidden part on the dash to hold my phone. ...the ball is 17mm diameter and should fit gps type stuff.
thingiverse
Ipad mini dash kit for volvo v60, this only fits the model with the 5 inch screen. ... No glue or double sided tape needed, this snaps into place as seen in the video: https://youtu.be/SOsNidMuVBo
prusaprinters
Dieser Halter ist für das ipad erstellt. ...Er ist klein, stabil, handlich und einfach zum drucken. This holder is made for the ipad. ...It is small, stable, handy and easy to print.</p>
thingiverse
This is just a little edited version of a mount, made to be slightly stronger and to better fit iPad's with Cases on like mine. You can use average print settings for this - Doesn't need support if you print it upright I hope you enjoy! ...
thingiverse
Simple design to mount any ball joint phone mount on VW Amarok Dash
thingiverse
This is a simple dash mount phone holder for an RX8. ...It follows the contours of the dash and allows a magnetic mount to stick to it.
thingiverse
Mounts right on vrs upper bolts. ...Its 60mm long and dash mounting end bolts are 112mm apart with 5mm holes.
thingiverse
For dash mount style panels where the mounting screw holes in the corners have broken off. AC panel in the boat is re-mounted good as new! ... Instructions Makerbot 2 Black filament, 0.2mm 1 layer 100%...
thingiverse
This is a simple dash mount I remixed to hold a backup camera screen for my RV, it would also work well as a phone mount with a magnet mount.
thingiverse
This is a dash mount for a Vapor on a DR650. Mounts between handle bar risers. I used brass inserts and m5 bolts to attach. ...I printed with carbon infused nylon but petg should work also.
thingiverse
On my black dash in the sun, it gets hot enough that PETG starts to sag and warp.** This is a dash mount I designed to go with a phone holder I designed for Autocross events. I have attached it to the dash using some of the 30lb Double sided 3M...
thingiverse
This is a rugged dash mount for a 2014-2019 C7 Corvette. It uses the AMPS screw pattern to attach accessories and I used ProClip mounts to attach a RasPi running OpenAutoPro. I used PLA because it's all I have but the design is reinforced and using...
thingiverse
Adapter to mount the Cygolite Dash to a GoPro style mount. No hardware required, just use the screw that's holding the loop onto the light. For increased stability, I added some zip ties onto the GoPro mounting point. ... This is still a work in...
thingiverse
- Xiaomi Yi Smart Dash Camera mount - Didn't want to remove original mount from my car when I traveled abroad and wanted to use the camera in rented vehicle... ... - Printed in PETG, 236C, 100%infill, 25% fans - Use thick, double sided tape to stick it...
thingiverse
I needed a mount for my dash cam because the suction cup was messing up my windshield tint. I would print this out of PETG or similar due to the heat. PLA+ works but gets very soft. ...I used 3M double sided automotive tape to mount it.
thingiverse
I made this to mount a picatinny holster to a dash. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/02qEjXELAoo Print Settings Rafts: No ...
thingiverse
... tested the fit and it fits perfectly without the iphone adapter bracket. NOTE: I used the flat dash mount from the cited source to design my mounting adapter. ...You will need to download it from the source page to print all parts of the design.
grabcad
This clip allows you to mount a dash cam to the passenger sun visor. You will require an M5 20mm cap head bolt, washer and nyloc nut. The nut in the picture was machined for the purpose, note the camera fitting is tapped M5 so the cap head bolt is...
thingiverse
When making your own parts simply create a negative of this (And add approx 0.2mm tolerance to all sides an an extra 0.4mm of depth) then glue and press them together All parts have an arrow on the unside to assist with orientation when gluing to...
prusaprinters
Dodge Ram1500 Backup Camera MountYear: 2015 Dodge Ram1500 (May fit other model years)Adapted to utilize existing holes for dash board coin area.Compatible for Type-S after market rear camera LCD, utilizing Bluetooth license plate camera.Additional...
thingiverse
... on snap fit for phone and back fitment for vent. ...Holds the phone at a better angle to view while driving. A simple clip for your dash vents to hold a phone. ...This model is specific to VW GTI (2015+) - and Iphone 8Plus in Otterbox case.