dc14 dyson 3d models
2490 3d models found related to dc14 dyson.
thingiverse
I adjusted this for my Dyson DC14, I think it will work with other older dyson vaccums. You may need to make the inner diameter slightly bigger, it is a tight fit, but i used sand paper and it works ok. ... Doesn't perfectly fit on vacuum since I lost...
thingiverse
Frustratingly, the cable clip on my trusty Dyson DC14 snapped, rendering a still perfectly operational device nearly unusable. ...Simply pop off the grey center cover, remove the Torx T20 screw, and swap it out for this replacement hook - and you'll be...
prusaprinters
Our Dyson DC14 upright took a bit of a tumble and the cord retaining arm broke. ...This replacement part is a fairly easy print (there are supports) and an easy repair.</p><p>Disassembly/Repair:</p><ol><li>Use a spudger (or sharp edge) to pop the gray...
thingiverse
A replacement part for the Dyson DC14 upright vacuum cleaner. This part replaces the wand release catch. ... Printing: Printed with ribs facing up Build-plate supports for at least 35 degree angles (MK3S+) PLA, 0.15 layer height resulted in...
prusaprinters
A replacement part for the Dyson DC14 upright vacuum cleaner. ...This part replaces the wand release catch.</p><p>Printing:</p><ul><li>Printed with ribs facing up</li><li>Build-plate supports for at least 35 degree angles</li><li>PLA, 0.15 layer height...
prusaprinters
A replacement part for the Dyson DC14 upright vacuum cleaner. ...This part replaces the wand release catch.Printing:Printed with ribs facing upBuild-plate supports for at least 35 degree anglesPLA, 0.15 layer height resulted in easy-to-remove supports...
thingiverse
We've had a trusty Dyson DC14 vacuum for years, but after its rugged handling the little tab at the bottom of the cord wrap snapped off, making it nearly impossible to fully wrap the cord in place. This simple fix prints out in two handy pieces. I...
thingiverse
Dyson's already used all the best places to keep standard the bits and bobs, and I struggled to find anywhere that was A) convenient, and B) didn't get in the way. But, whilst emptying the bin the other day, I noticed there was enough room to get a...
prusaprinters
... the gaskets seal tight. Dyson states you carry it by this handle. I believe It should have been more stout, using more plastic. ...This addresses and fixes that.</p><p>I also included a mating top part if you want a round handle.</p><p> </p>
thingiverse
The cord holder on my Dyson DC14 vacuum cleaner snapped off. There's no replacement part available on the Dyson website without shelling out $51.99 for the entire wand handle. So, I measured up the broken piece and came up with a 3D printable design...
thingiverse
The Dyson DC14 upright vacuum cleaner mounts the crevice tool on the side using a removeable C-clamp mount. After some time the ABS plastic breaks down or is affected by weather etc and removing the crevice tool can rip out or damage the mount. ...
thingiverse
This tool is designed specifically for the Dyson DC04, however, it can also be utilized with the DC03, DC07, DC14 and DC33 models as well.
thingiverse
It's designed to be compatible with the OEM replacement part Dyson DY-92119801, and that part replaces DY-90424304, 904243-13, DY-90424309, DY-90424314, DY-90424315, 904243-15, 904243-09, 904243-14 and 921198-01 on several variants of the DC07,...
prusaprinters
This model adapts the Dyson DC14 Turbo Tool (~2006) to the Dyson Ball Animal 3 (UP30 - 2022). ...Snaps into place via the retention clips on the Turbo Tool and the Dyson Ball Animal 3, respectively.Use supports for recessed tube and cuff (see gcode)Use...
thingiverse
A jig to secure clutch/brushbar belt tool for the DC14, see photos
thingiverse
I need an adapter to utilize my previous Dyson DC08 accessories, such as tools and brushes, on my recently acquired Dyson DC50 vacuum cleaner.
thingiverse
When my Dyson DC14's "Turbine Pet Hair Attachment Tool" stopped working, I promptly ordered the newer model, the Tangle-Free Turbine Tool, directly from Dyson. Unfortunately, it doesn't fit, and there's no adapter available for my DC14 since it's an...