deadpool sword sheath 3d models

Dorsal sheath of deadpool swords. ...Printing in 0.2mm filling 15%

... The Sheath was designed to allow both swords to be inserted at the same time. For a little more flair i created the deadpool logo to it. Thoughts or comments are welcomed. I hope you enjoy as much as i did designing and playing around with it.

This is the low-poly deadpool sword from the game. ...If you want the high-poly 100% movie accurate files contact me for info.

had some issues with printing the original sword (https://www.thingiverse.com/thing:2743205), which has to be printed standing up. ... so i have split the original in half and you can print it laying down at, takes 40 minutes for 1 sword.

I remade the Sword Sheath so it can hold 2 swords, just in case Deadpool decides to use his guns hehe

so this my sword and sheath. ...if the sword doesn't fit in the sheath please tell me so i can fix it

I printed on FDM ender 3 printer Model content: Sword(171mm) - if the sword does not print well (171mm) i stay it on 60 degrees Sword-hand-1(72mm) Sword-hand-1-with-support(73mm) Sword-hand-2(72mm) Sword-hand-2-with-support(73mm) Sword-part-1(85mm)...

Just a small sword with a sheath. ...Inside of sheath may need to be cleaned out after printing to remove loose pieces of plastic hope you like it

This is a sword and sheath model i designed in Blender 3D.  both models are large in scale.  when 3D printing this in resin i scale the model down to: 70% for the sword and 75% for the sheath. this way the clearence is wide enough for the sword to...

It's a sheath for the Master Sword from the Legend of Zelda games. ...I haven't tested it yet to see if it fits the 3d model of the Master Sword I made yet.

I wanted a sheath to fit this Master Sword: https://www.thingiverse.com/thing:3647786. Super mini version of the sword. But when printing so small, the keys would show through. So I took out the little holes for the keys, merged all the parts...

  I decided to 3D Model this sword and sheath using Rhino after seeing lots of master sword models out there, but not one representing a full scale 1.2meter long sword from The Ocarina of Time. This is perfect for cosplay as Link! The Sword is...

Files contain the complete sword and sheath in one piece (.OBJ) and also both models are cut into smaller pieces (.STL) designed for 3d printing. SCALE At 100% scale the sword dimensions are: Width approx. 83 mm Length approx. 1000 mm Height approx....

I printed on FDM ender 3 printer Model content: handle-1(81mm) handle-2(81mm) ring_1(17mm) ring-2(18mm) sheath(172mm) - I recommend printing at an angle of either 45 degrees or 60 degrees, so that there are no supports inside, also reduce the...

If you want more information and to see it more closely, watch this video: This is the sheath that goes along with the Master Sword I created here: https://www.youmagine.com/designs/master-sword-full-size-legend-of-zelda I created this sheath in...

This is the sheath that goes along with the Master Sword I created here: https://cults3d.com/en/game/master-sword-full-size-legend-of-zelda I created this sheath in Fusion 360 along with the sword. I printed this on my Robo 3D R1 using Hatchbox White...

If you want more information and to see it more closely, watch this video: https://youtu.be/Za5byBQs0I4 This is the sheath that goes along with the Master Sword I created here:...

Master sword Sheath real size: https://www.thingiverse.com/thing:3720143 The different parts are separated to be printed in the right color plastic or painted before assembly. Be careful not to paint the interior of parts A, B and C, the paint will...

If you want more information and to see it more closely, watch this video: https://youtu.be/Za5byBQs0I4 This is the sheath that goes along with the Master Sword I created here: http://www.thingiverse.com/thing:1449187 I created this sheath in Fusion...

Long Sword game ready model Asset Store link: -link removed-

... file for the sword holder on the back. ... I designed this for reasons because the plastic swords were bad when I printed them and decided to make them from metal so they look more real (aluminium 1mm,, imbus screw, wall plastic anchor, and washer)

Made for the Witcher Ciri sword for a cosplay. ...No supports needed

The sword blade could be too thin, but you can just modify it.

... . ...The upper and lower parts are printed with a layer of 0.1 mm. The remaining parts are printed with a layer of 0.3 mm. After gluing all the parts, the upper and lower parts are painted under the metal. The sheath is wrapped in artificial leather.

... . ...The upper and lower parts are printed with a layer of 0.1 mm. The remaining parts are printed with a layer of 0.3 mm. After gluing all the parts, the upper and lower parts are painted under the metal. The sheath is wrapped in artificial leather.

The Gladius Sword helped Rome cut a bloody swath throughout Europe and the Mediterranean and forge one of the greatest empires in history. This Game Res was created in 3DS Max. Textures created in Substance Painter. Poly count: 5,906 and Tris Count:...

I made this for a cursed nail sword from chainsaw man. The print is about 75.5 cm or about 30 inches and about 2.7 cm or a little more than 1 inch wide. I printed it at 20 percent infill with no supports. ...Also it is my first file I've made and isn't...

Have you always wanted to wear your USB flash drive casually on your hip in the shape of a sword? ...Then I have the perfect solution for you! I present: The USB sword sheath

Inspired by the Deadpool movie, full sized version of swords and back sword holder. holder has no attach points, I use velcro on mine. ...supports will be needed on most parts, but try to limit supports on the scabbard pieces, it gets annoying trying to...

**Dread Pirate Roberts sword sheath from The Princess Bride** Printed in PETG and 0.2 layer height. It is convenient to add some brim to all the pieces Supports only needed for the sheath_up. Sheath interior pieces are numbered in the upper side:...