deck bix 3d models
13349 3d models found related to deck bix.thingiverse
A replacement label rail for BIX telephone punch-down frames. ...I had a few frames at work that were missing label rails so I made this up and printed replacements.
thingiverse
This is a tool to insert ethernet wires into an BIX patch block. This is NOT a 110 tool. The print does not require support. The 100% infill print takes about 1.5 M of the 1.75mm filament. The tool worked fine with 20% infill. ...
thingiverse
The Bix 3 includes a laser cut FPV mount, but I still decided to make my own to fit my pan/tilt mounts linked below. CCD Pan Tilthttp://www.thingiverse.com/thing:592448 Fatshark 600tvl cmos Pan Tilthttp://www.thingiverse.com/thing:401461 I dont...
thingiverse
Scanned with The Scan-O-Tron 3000 (http://www.thingiverse.com/thing:127968), ReconstructMe (http://reconstructMe.net) and an Xbox Kinect at the Great Fredini's Coney Island Scan-A-Rama booth at the 2013 World Maker Faire New York. The Great...
thingiverse
Customized version of http://www.thingiverse.com/thing:1515242 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1515242 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:175150 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=175150
sketchfab
Deck, part of a medieval fantasy environment scene. ... www.artstation.com/artwork/rkkg2
thingiverse
Designed this deck for my father. ... It is close to scale, designed to represent a 12 foot square deck. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/hZynmC53IzE
prusaprinters
It is close to scale, designed to represent a 12 foot square deck. This thing was made with Tinkercad. ...Edit it online <a href="https://www.tinkercad.com/things/hZynmC53IzE">https://www.tinkercad.com/things/hZynmC53IzE</a></p> Category: Outdoor &...
grabcad
My new Deck or Porch. The support columns are telephone poles. I started building this on 10/13/2012. I had to build the pole crane to winch and set the telephone poles. They weigh about 1000 pounds each. I have 4 poles left to set into place. ...I...
thingiverse
This design is for those wo are fed up with the original motor mount which is a joke regarding accessibility and serviceability. Use this design if you want to change the motor easily, even on the field. ... - 4 screws fastening with washers -...
thingiverse
Hello folks, I'm a backdrop builder with over 15 years of experience. You can see my work on my Instagram or Youtube channel. Thank you by following me or send me a tip. ... best regards Nerfi_Star See my Work: Instagram: NERFI_Star ...
thingiverse
For mounting board cameras securely onto the plywood FPV pod that comes with the Bix3. 30min Epoxy and 4 M2 nylon screws/nuts/spacers are needed. ...
thingiverse
Hello folks, I'm a backdrop builder with over 15 years of experience. You can see my work on my Instagram or Youtube channel. Thank you by following me or send me a tip. ... best regards Nerfi_Star See my Work: Instagram: NERFI_Star ...
thingiverse
Hello folks, I'm a backdrop builder with over 15 years of experience. You can see my work on my Instagram or Youtube channel. Thank you by following me or send me a tip. ... best regards Nerfi_Star See my Work: Instagram: NERFI_Star ...