delta 36725 table saw 3d models
140542 3d models found related to delta 36725 table saw.thingiverse
I made this to fit the miter slots on my Delta 36-5000 table saw for a cross cut sled. ... It should fit the Delta 36-725 as well.
cults3d
I made this to fit the miter slots on my Delta 36-5000 table saw for a cross cut sled. ... It should fit the Delta 36-725 as well.
thingiverse
Just an attempt at recreating this table insert, for my dads table saw, there are 2 parts to this, the slot and the tongue
thingiverse
12/4/2020 This is a table saw sled runner for my ancient Delta Table saw. It should fit tight in the slot as any 5/8" saw slot. Side to side tolerances are less than .5mm on my saw. ...
thingiverse
Delta 725T2 Vacuum port adapter for shop vac. 2.5" ID to 1.75" ID. ... It's a little snug, maybe scale to 101%.
thingiverse
This replacement table insert fits Delta's 28-160 Band Saw. ... Print upside down.
thingiverse
This is a throat plate I made for a mid 90s Delta Table Saw. ... Just Glue together and drill your bolt holes.
thingiverse
The rear cover/brush holder for the motor on my Delta table saw was damaged and I really needed to replace it to make the saw safe again. ... Now you can too!
thingiverse
Table insert for a bench top delta scroll saw Model 40-530. 2.6" diameter upper and 2.2" diameter lower. Fits perfectly! Included STL and Sketchup model. Instructions Print it, then insert in saw table. ... No need to remove blade, small slot allows...
thingiverse
This is a replacement handle grip for the Biesemeyer fence that comes with a Delta model 36-725 10" Contractor Table saw. The metal pin that the grip fits over has an M6-1.0 thread in the base. ... This thing has a hole in the bottom so you can add the...
thingiverse
Zero Clearance Insert for the Delta Model 34-670 10" Contractor's Table Saw. This can be machined from phenolic, aluminum or acrylic stock. A ZCI is used to provide a smooth, gap-free work surface on the saw without a space for narrow cut-off pieces...
thingiverse
This is a switchbox for a modern day on/off switch to replace the original switch for a Delta Rockwell table saw made in 1948. The saw runs like a top and with the exception of the Biesmeyer Fence and a junky little sheet metal motor cover it is...
thingiverse
Saw a YouTube video on stopping dust from falling to the floor using the Delta 36-725 or 36-5000 table saw. Credit goes to Richard Crees and his YouTube channel for designing the wood and sheet metal version of the dust catch that inserts into the...
cults3d
I have a small shop and have to move my Delta Unisaw all the time. ... The hose in the back kept getting snagged since the saw pretty much sits against a wall. ... Modelled this so the saw can be up against the wall and the hose does not get in the way.
thingiverse
The hose in the back kept getting snagged since the saw pretty much sits against a wall. Modeled this so the saw can be up against the wall and the hose does not get in the way. 11/12/22 added a vertical port. ... Changed up the dust collection in...
prusaprinters
This adapter connects a Shop Vac 2.5" hose to the dust funnel on my Delta table saw. There is a screw-on trap for easier removal of long, thin pieces of wood that might fall through the saw. ...There are two screw holes for mounting the adapter to the...
thingiverse
Delta table saw fence rear foot. Part number 422-19-048-0001. Used on UniRip Fence part number 36-448. Part discontinued by Delta. Print Settings Printer Brand: RepRap ...
prusaprinters
This tablesaw dial gauge holder is made to fit directly in the slot machined into the table of my Delta saw. The gauge is used to measure the distance from the slot and the blade at front and back to insure the blade is aligned correctly. ...It is a...
thingiverse
This is a Fence organizer for the Delta 36-725 table saw (it may fit other models also. I designed this to friction fit inside the fence so it is easily remove-able as needed. It the current setup it hold a push stick, glasses, pencils, and small...
thingiverse
A drawer that fits in the hollow square fence tube of a Delta 36-725 table saw. Due to the nature of printing I made the drawer face separately and glued it on with CA glue. This gives a pull tab and a stop so the drawer doesn't go too far in. There...
thingiverse
The end cap of the sliding table telescopic stop of my Bernardo FKS table saw broke, so I designed a new one. Fits just like the old and uses the same screw in the same location, of course. Die Verschlusskappe des Teleskopanschlags meiner Bernardo...
prusaprinters
The end cap of the sliding table telescopic stop of my Bernardo FKS table saw broke, so I designed a new one. Fits just like the old and uses the same screw in the same location, of course.</p> <p>Die Verschlusskappe des Teleskopanschlags meiner...
thingiverse
This part has an ID of 2.5" and snugly fits over the Delta's dust port, which is 2.49". It was printed at 0.15" thickness which was the same thickness as a store-bought adapter. ...The opposite end is 3.9" OD, and my flexible 4" dust collector hose fits...
thingiverse
I saw in the comments on the original makers upload that everyone had an issue with printing it as it was so I fixed the original file for everyone's use Edited: removed a small piece left on front tab that prevented seating properly
thingiverse
New handle for delta mitre saw model 36-220C Wall thickness 2 mm inflill 25% PLA
prusaprinters
This is a zero clearance insert for a Delta Rockwell 14" band saw. ... It was modelled on a 1950 model, but should fit a wide range of vintages.</p> <p>Fusion 360 model file is included if you need to tweak it.</p>
thingiverse
Replacement plug for a Delta bandsaw when the original aluminum one gets completely worn out. Designed upside down and should be flipped on its axes to print. That will eliminate the need for supports and will keep the surface nice and smooth.