delta sander 31 460 3d models
35272 3d models found related to delta sander 31 460.thingiverse
Shop Vac hose adapter for Delta 31-460 Belt Sander for old style that has no vacuum orifice
prusaprinters
I also needed a fence, so I made one of them tooThis mates an older Delta belt sander up to a standard 8 gal (30,3L) ShopVac hose to collect dust and dirt from your sander, keeping you area clean and organized of dirt.Printing requires supports and...
thingiverse
Basically used the lower pulley from elfworks Sears Belt Sander Pulley Set, and then whipped up my own for the upper pulley. ... Print at 100% infill.
thingiverse
Was asked to remix the remix. :) This should have the correct tooth spacing to match the diameter of the pulley. ...(24mm vs 16mm = 150% more teeth.) If I were to print a top cap, it would be printed separately, and glued together, as shown in...
prusaprinters
<p>Was asked to remix the remix. :)</p> <p>This should have the correct tooth spacing to match the diameter of the pulley. ...(24mm vs 16mm = 150% more teeth.)</p> <p>If I were to print a top cap, it would be printed separately, and glued together, as...
thingiverse
Both of the pulleys/rollers/drive wheels on my Delta 31-050 grinder/sander failed (one exploded) So I modeled up some replacements. Nothing special, just going off the measurements, the originals have a curve, but the design is flat. In the original...
thingiverse
I bought a secondhand Multitool recently and realised it didn't come with a sander attachment. This 3d print is specific to my Einhell Multimaxx but should fit most other tools. To finish, it just needs some Velcro© loops to allow the...
thingiverse
As I did not want my delta sanders sanding paper disks to be flying around I designed this box. This fits standard 93mm sanding paper disks. You may print this in any material of your choice. ...I gave it some 30% infill which is absolutely enough...
thingiverse
Adapter for dust collection from a Bosch Delta Sander PDA240E. The vacuum cleaner I use is a Nilfisk. ...Printed it with NylonX
thingiverse
This is a replacement hinge for the disc table on a 4"/6" Delta Belt/Disc Sander. ...The original part is metal but I printed the replacement in PETG and it seems to be holding up fine so far.
thingiverse
This is a replacement motor cover for a Delta 1" Belt Sander. I'm sure it may fit others. It is a tight fit and is thick and durable. I used an Imperial Logo (http://www.thingiverse.com/thing:1114731) at the end just to give it some personality...
thingiverse
I got an older Delta 12" disc sander which is a wonderful machine, but it has a really unusual dust collection hookup. You can find the adapters on eBay (either for $$$ in cast iron or $$ for a 3D printed one) so I figured I'd make my own. This fits...
thingiverse
One of my detail sanders landing in a bad way from a fall onto a concrete floor. Rather than trying to source out a replacement head I just printed one out in 3 hours. Gotta love having a personal factory at your fingertips. The original part was...
thingiverse
I liked the Craft sander that Bernbout made but I wanted to fix some things and now you can print my new and improved version!
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1148986 Instructions Using the following options: letter_3_space = 10 letter_2_space = 10 Font_name = Chewy letter_1_height = 6 center = 20 Loop_y_position = 0 letter_2_height = 5 letter_4_space...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_outline_style = rounded whichextruder = extruder1 bar_width = 5 font_size = 12 writing_direction = ltr minimal_color_layer_thickness = 0.6...
youmagine
These are two delta sander adapters for the Bosch GOP 10.8 Cordless Multi-Cutter that can become convenient if you have to sand in confined spaces. ...The small adapter has a diameter of 40 mm which results in an edge length of about 35 mm and the...
thingiverse
These are two delta sander adapters for the Bosch GOP 10.8 Cordless Multi-Cutter that can become convenient if you have to sand in confined spaces. ...The small adapter has a diameter of 40 mm which results in an edge length of about 35 mm and the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1562501 Instructions Using the following options: handleOuterDiameter = 80 rTransitionFillet = 10 boltDiameter = 0 boltHeadThickness = 24 baseHeight = 13 boltHeadHeight = 0 rCounterboreFillet =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_step_shape_degrees = 45 resolution = 0.5 countersink = 2 non_thread_diameter = 0 type = nut head_diameter = 12 texture = exclude...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: text_thickness = 4.2 outline_thickness = 3.0 bar_style = bar_only lug_width = 0 border_width = 0 bar_shift = 12 font_size = 32 bar_width = 48.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: whichextruder = monochrome outline_color = Gray bar_length_trim = -11 lug_text_distance = 4 font_name = Exo text_color = DarkRed bar_thickness =...