desk camera stand 3d models
289091 3d models found related to desk camera stand.thingiverse
This is a simple 1 axis desk stand for cameras. You can mount actioncams, small DSLR cameras (~600gram), microphones or your mobile phone onto it. I like to use it if i want to film solder work, for this it works quite nice. You will need 1 M3...
cults3d
This is a simple 1 axis desk stand for cameras. You can mount actioncams, small DSLR cameras (~600gram), microphones or your mobile phone onto it. I like to use it if i want to film solder work, for this it works quite nice. You will need 1 M3...
thingiverse
**More information and photos of the project at:** https://daumemo.com/diy-camera-desk-stand/ **My other projects:** [daumemo/designs](https://www.thingiverse.com/daumemo/designs) Dremel Drill Press [![Dremel Drill...
thingiverse
You will need: 2 x 1/4-20 UNC bolt 1" Long For main camera mount 2 x 1/4-20 UNC bolt 1.5" Long For the two tilt mechanisms 3 x 1/4-20 UNC Nuts 1 x 1/4-20 Washer The pics should give more than enough detail on how it goes together. I used a 6.5mm...
thingiverse
As the new GoPro Hero 9 supports webcam mode a desk stand for the GoPro is a good idea. or use older GoPro as webcam via the hacks / mods that are out there for it. UPDATE:: Added a V2 version that have longer and wider legs and a wider base,...
prusaprinters
Desk stand for GoPro. As the new GoPro Hero 9 supports webcam mode a desk stand for the GoPro is a good idea. or use older GoPro as webcam via the hacks / mods that are out there for it. UPDATE:: Added a V2 version that have longer and wider legs and...
thingiverse
The main problem is in camera holder: M6 screw could damage the camera, 1/4" is preferrable. So it is. Camera holder: support 1/4" screw (for example, type D here: https://aliexpress.ru/item/1005001453291034.html). Suitable for Nikon camera. Desk...
pinshape
In the photograph you see my first design ... it works, but after building this I realized the parts I've posted here are a better solution. The 4' long 1/2" diameter dowel rods are cut in half for the legs and side to side cross bars ... ...the side...
thingiverse
The Ubiquiti G3 Instant has a small base and is easily knocked over. Simply setting it on a shelf doesn't allow and vertical adjustment. ... This mount is a little more stable than simply setting it on a surface and allows full articulation up or down...
thingiverse
I needed to mount this ridiculous "web camera" on my desk, it has a 150mm dome, and I have a 140mm UP! printer. This is what I came up with, and amazingly it works quite well, and is fairly stable. ...
thingiverse
This is a screw into your desk camera stand. I recommend abs filament. This is for presentations on a flat surface. the little slot on the top are for rubber bands to hold your computer. ...
grabcad
To go in stand mode you just lift the board and with lifting the left side higher like the right one the Stand desk is locked on top position. To go in sit mode lift the right side of the board and push the left side down, and the desk is going down...
thingiverse
I just increased the size of the stand from http://www.thingiverse.com/thing:1248484 to 14cm. The small one was falling over, as i had my camera quite high. The options were either to stick it to the table or increase the size. Sticking is not an...
thingiverse
This is a replacement mount for a desk mounted microphone arm so it can be used as a mount for devices or hardware using a standard camera mounting screw.
cults3d
This multi Part 3d Model is an Adjustable Camera or Webcam Holder that is perfect for a desk or for online meetings. It has a modern and hexagonal design and the height can be adjusted to 5 heights. The end can either be one of the 2 included...
grabcad
Two axis camera stand which move simultaneously both vertical & horizontal say X & Z axis of stand on which camera mounted.
thingiverse
A camera stand designed to sit on the extruded aluminium of the Velleman K8200 to raise the camera high enough to watch the print progress.
grabcad
Camera Stand AssemblyKindly like and give feedback in commentsfor Q/A & project reach out atazanch04@gmail.com
thingiverse
... https://www.thingiverse.com/thing:4885570. ... The mount was changed to mount to my desk and the arm was shortened. Thanks for the original. Please think about buying me a coffee. ... https://paypal.me/rob180sx3D?country.x=CA&locale.x=en_US
thingiverse
Camera stand with storage bins. Used to hold Octoprint HD camera for 3d printing. I put coins in bottom bin to add weight. Also added rubber feet. Lay flat on back to print. Needs supports on shelf fronts but ovals should be ok without. ... ...
thingiverse
I needed to make a quick camera stand for my Logitech HD Webcam 310 to monitor my print jobs. It is a little rough but it does the trick. Please note that you will need supports to print this and the fittings can be a little tight, so working them...
thingiverse
Wifi camera stand for use to monitor printer progress. It's a fairly wasteful design, if I had to do it again, I'd print it in two pieces. Slides for over the workbench and works nice. ...Second file is just a bushing made for the gap on the mounting...
thingiverse
This is an ugly camera stand that uses a diving weight (or something else in the box ) as a counter weight to the camera . I wanted the smallest possible foot print and I also wanted to be able to use my web cam with my computer . So I came up with a...