desk gromet 3d models
42930 3d models found related to desk gromet.thingiverse
A simple ceiling gromet. ...It's an incredibly tight fit, definitely some hammering is needed!
thingiverse
Used to add the gromets for cables to the bottom of the Thermaltake w200
thingiverse
Simple drywall gromets for cable management, there are a closed, open and 2 cables (8mm) version. It fit in a 2in hole. ... Designed for 1/2 drywall Enjoy!
thingiverse
A 2 piece cable gromet completely customizable with Fusion 360. ...it is a 2 piece gromet so that you can drill the hole big enough so you can also pass the plug trough, en then plug the rest of the hole.
thingiverse
My wife and I had an idea for a monitor mount that was functional and easy to use. ...Born from that was the gromet, used to stabilize the pole mount at the top.
prusaprinters
Simple drywall gromets for cable management, there are a closed, open and 2 cables (8mm) version. ...It fit in a 2in hole.</p> <p>Designed for 1/2 drywall</p> <p>Enjoy!</p> Category: Household Supplies
thingiverse
Dash panel(Suzuki or Toyota mid 90s I think, I was only given the part to copy) plastic pop-in gromet, this probably needs a bigger cube for longer pop-in ears as this was not a tight fit, I should probably have also made it solid rather than copying...
grabcad
Star gromet / bushing for through panel routing of wires, tubing, or pipe
thingiverse
I made this for a wood work project and is glued in, not High Tech, just thought I would share it. ...For a 20mm Hole 20mm insert large O/D 30mm I/D 13.5mm 2.3mm thick If you remix this or make alterations, please upload them back with all original...
prusaprinters
Plug to close a double table gromet hole. Each gromet whole is 58 mm. The intersection where they meet is 35 mm. Printed on Prusament JetBlack with 15% infill. No supports needed. ...If you use the STL file, rotate it upside-down.</p>
youmagine
im using it on side of plywood box for a power cord exit, using it with waterproof wire gromet i bought from ideal supply hole in center in 17.2 mm
thingiverse
This is a faceplate with a VGA port, a keystone jack, and a Video port with Gromet setup on it. This was taken from the WALLY - Wall Plate Customizer - http://www.thingiverse.com/thing:47956. Updated just about 4pm on 10/8 after realizing a face...
grabcad
A 3d printable watertight rubber gland. For those of you that dont want to buy 20+ of them off amazon when you only need like 2.Pprinted with petg(white) and tpu(red) 0.15mm layer height. Tested several different designs at depth of ~3in. They lasted...
thingiverse
This is the gromet that holds the top engine cover on a Ford 2.0 TDCI engine. 4 are required. ...I printed them in TPU with just 1 wall and 15% infill to endure they were nice and soft.
thingiverse
Spare part grommet, adapter, connecter to replace a lost piece for my Breville hand blender and chopper. ...The gromet sits in the top of the chopper lid to connect it to the blender motor handle.
cults3d
Spare part grommet, adapter, connecter to replace a lost piece for my Breville hand blender and chopper. ...The gromet sits in the top of the chopper lid to connect it to the blender motor handle.
thingiverse
This is a modification of the original filament sensor box for the Prusa Mini (from R8 version) modified to fit the rubber gromet that retains the Palette 2 PTFE tube. Tested and working great. Print with 4 walls for strength. ...
thingiverse
Flexible - cable gromet Here is a hose tip for a sheath with an outer diameter of 10.30, 9.35 et 8.5mm. This end piece holds the flexible sheath by screwing its groove. Layer thickness 0.2 Hull thickness 1 Fill rate 25 Temperature of 220C ° printing...