desk purse hook 3d models
95655 3d models found related to desk purse hook.cults3d
Simple modern table edge hook to hang a purse or bag. Designed for FDM printing. Long and short hook model included. It is recommended to add a foam pad or double stick tape where the hook rests on the table in order to prevent the hook from slipping...
thingiverse
My wife asked for a purse hook she could hang her purse on it so she would not have to set it on the floor. ... hang hook on edge of table, put purse strap in small hook
myminifactory
This is a simple hook that clips on to the center console so you can hook a purse off it. This prevents the purse from falling over and spilling out on to the floor. ... Designed for the 2015 Honda Civic.
thingiverse
The fact that their's has the forward angle forces the center of gravity towards the desk and thus keeps the hook on the table. The issue I fixed with it is adding the rounded surface that the bag handle hangs from and also removed the angle...
thingiverse
Based on the standard design of the old good https://en.wikipedia.org/wiki/Purse_hook I wanted to print one for my wife but couldn't find it so I tried to make it on Tinkercad. This is my first submit so I know there is still a lot of room for...
prusaprinters
I based the shape off of https://www.thingiverse.com/thing:2269715.The fact that their's has the forward angle forces the center of gravity towards the desk and thus keeps the hook on the table.The issue I fixed with it is adding the rounded surface...
cults3d
... (10 cents, 20 cents, 50 cents, 1 euro, 2 euro). The desk coin purse is also equipped with a practical bowl, useful for holding the smallest coins (1 cent, 2 cents, 5 cents) Perfect for holding loose change on the desk in your workplace and at home.
thingiverse
Here is a purse holder hook thing that goes on right behind the seat of the car. ... All you have to do is take the head rest out slide the holder over the head holder rails and just put the head holder back in place, the holder is probally going to be...
thingiverse
The perfect little hook for hanging all your bags or purses on a standard closet rod. A soft curve on the strap holder prevents leaving sharp edges on items such as leather bags. ...This part was designed to be fairly heavy duty and can hold a good...
thingiverse
Print the hook with 100% concentric infill for strength, the Venuses can be printed lighter as they don't support any weight. I used silk purple PLA, but I intend to print a new one in ABS when I get some. Once done just knock off the bumps with some...
myminifactory
This hook was designed to latch to either of the 10mm (diameter) rods that stem from the headrest and connect to the seatback. Specifically designed for the headrest of a 2005 Toyota Corolla CE. ...Can be printed without support.
thingiverse
Cabinet hook for Purse/Handbag Schrankhaken für Handtaschen.
thingiverse
This portable coat and purse hook follows the basic C-clamp mechanism to safely secure your purse and coat to any table up to 1.75in thick. Its small design (about 5in tall and 3.5in wide) means you can store it easily and take it with you wherever...
thingiverse
This is a hinged version of my "Purse Hook for Audi TT RS (2012)." The hinge allows the hook to fold up out of the way when there are passengers in the backseat of a sedan. I used M6 heat-set inserts (https://www.mcmaster.com/#94180a371/=178412o)...
thingiverse
Unfortunately it didn't have a convenient place to hang or place her purse while driving. She asked for a hook which can attach under the headrest to hold her bag and this is what I came up with. Rev 1 - Uses a pin to hold the halves together and...
thingiverse
I had made some seat back hooks from thingiverse for trash and my mom wanted a set that could hold her purse so I got out the calipers and took some measurements and printed this. It was designed around the headrest of a 2015 Ford Edge and the back...
thingiverse
This attaches to the front passenger seat headrest posts, providing a hook in back of the seat on which you can hang a purse or bag. It is quite strong and installs with two screws in a minute. The assembly is easy to remove if needed. Print Settings...
thingiverse
This multicolored portable coat and purse hook follows the basic C-clamp mechanism to safely secure your purse and coat to any table up to 1.75in thick. Its small design (about 5in tall and 3.5in wide) means you can store it easily and take it with...
cults3d
Pocket Coin Purse for Men and Women It can contain up to 50 coins (7/8 coins per type) of 2 euros, 1 euro, 50 cents, 20 cents, 10 cents, 5 cents. and 2 cents. Compact, to divide coins from 1 cent to 2 euros. To save time in finding the right coin. ... ...
cults3d
Cute 3d purse, handbag, bag model in .STL format. Suitable for using as a keychain. I designed it from scratch and it 3d prints well with any WOOD PLA (or any other material such as GOLD SILK or regular PLA etc...). No need for supports. If you want...
youmagine
You may print this purse with soluble support as a completed assembly if you have a large dual extruder fused deposition modelling additive manufacturing machine; 1. dual extrusion - nhandbag1pciii.stl with phandbag1pciii(1).stl2. dual extrusion -...
thingiverse
Adaptation of the desk hook by Tosh. This version is the 20mm hook and I have removed the protrusion from the top for a more flush mount. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: Doesn't Matter...
thingiverse
... of http://www.thingiverse.com/thing:44705 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44705 Instructions Using the following options: depth = 50 jack = hook_height = 35 desk_height = 17 width = 30 thickness = 10
prusaprinters
Hook that goes into standard desk hole and hangs off of the edge so I can coil my VIVE wires off the floor when I'm not using it. Category: Organization
thingiverse
Hook that goes into standard desk hole and hangs off of the edge so I can coil my VIVE wires off the floor when I'm not using it.