desk speaker mount 3d models
389872 3d models found related to desk speaker mount.thingiverse
Customized version of https://www.thingiverse.com/thing:300865 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=300865
thingiverse
... Notes: Printed with PLA at 102%. Dimensions are important because the holes must match up with both the Jerker desk mounts and the holes on the bottom of the speakers.
thingiverse
This is a desk mount for the Klipsch ProMedia 2.1 speakers. It is designed to be used with desks 1" thick. The mount has an interference fit on the desk corner and is angled at 45°. I've designed it to be rigid enough to not wobble if your desk...
thingiverse
i just wanna something so i can have my right speaker beside my pc monitor and no at the back where i lose so sound quallity but my desk is too small. so i make this mount to sit on. does the job nicely. you only need to screws to mount it. ... 15%...
thingiverse
I designed this stand to mount my Paradigm Atom bookshelf speakers on my desk at the ideal listening height while leaving space underneath to run cords. Small cutouts on the top allow for standard 3M rubber feet (13mm) to be mounted to isolate from...
thingiverse
This is a speaker with an upwards angle of around 12 degrees, which I designed to better angle the speakers I have on my desk upwards towards my ears. The stand features a small lip along the side and a larger stopper at the back to keep the speaker...
thingiverse
... concept, trying to build something small and discrete that doesn't sound it. ...This time I've used a small set of passive speakers. I like the idea of a small unobtrusive speaker, that doesn't dominate the limited amount of space on typical desks.
prusaprinters
A desktop stand for "5-inch" class monitors or bookshelf speakers.Raises the speaker off the desk so it takes up less room, and angles it upwards at 15 degrees to better point at the listener. Suits speakers with a footprint about 6.5 inches square,...
thingiverse
Raises the speaker off the desk so it takes up less room, and angles it upwards at 15 degrees to better point at the listener. Suits speakers with a footprint about 6.5 inches square, which is a fairly standard size for speakers with a 5-inch main...
thingiverse
... wanted a basic speaker for her computer, so I made this. ... I used 2 of 5W speakers and a 5V amplifier (both linked below, they're not my affiliates! Use whatever speaker you want!) Speaker: https://amzn.to/2KmbsGU Amplifier: https://amzn.to/3qKDlcN
cults3d
... by monitors. ...This mount screws into the VESA mount and uses a dovetail joint to support the speaker mount to hold the speaker above the monitor. ...this is sized for a Dell 24" monitor and the speaker mount is setup for Logitech G51 speakers.
thingiverse
... by monitors. ...This mount screws into the VESA mount and uses a dovetail joint to support the speaker mount to hold the speaker above the monitor. ...this is sized for a Dell 24" monitor and the speaker mount is setup for Logitech G51 speakers.
thingiverse
Wanted a small compact speaker mount that keeps my speakers as close to the wall as possible. But couldn't find any. So I made this. ...Enjoy :-) The mount keeps the speaker at a 20 degree angle to the wall.
thingiverse
cylIr is the radius of the speaker cylHole is the opening of the mount holdingRimH is the thickness of the retaining ring holding the speaker in after getting something that fit my speaker, I then tweaked the tabOffset to moving the retaining bumps...
thingiverse
universal speaker mounts for surround sound speakers that use a single m4 bolt to mount, approx 10mm thick where the bolt would pass through, can swivel 180 degrees, has 2 screw holes to mount to wall, can hold a 5+lb speaker with ease when printed...
thingiverse
I specifically designed it for mounting the center channel speaker beneath my TV. Part 1 is installed on the back of the speaker at the top. Be sure that whatever screws you use sit flush with the part. Part 2 is attached to the wall using...
thingiverse
In the lack of a good speaker foot/mount, I decided to make something original. This is what it ended up being. At first I was a little afraid of the balance, but it turned out great. Easy and straight forwards ;) ...
thingiverse
Heaving limited desk space I decided to create something that I could attach to my computer speakers on which I can hang my headphones. The speakers I have are the Creative GigaWorks T40 Series II 2.0 and the headphones I have are Corsair VOID RGB...
thingiverse
Speaker stand that fits in the cable holes of my desk (likely many others) The middle stand is a 40mm plastic drain pipe cut to fit the height I wanted. The cylinder provided is to be printed in vase mode and just used to hide the drain pipe. ...
thingiverse
I neede a small neat wall mount for my ELAC Center Speaker, so i created this little mount. You need a 6mm bolt/Screw to mount the speaker. ...The drill hole normal is 7mm, i used 6mm to add a liitle bit down tilt to the speaker and it worked very well.
cults3d
It also has an adjustable back stopper to catch the speaker in inclinded positions. It must be completed with some anti-sliding pieces at the top and the bottom of each leg, I provided the files so you can print them with TPU or FLEX fillament (you...
thingiverse
Prototype for a desktop speaker set to be used with my pc without needing a sub. Designed using WinISD to tune the port for 40Hz. ...Have not printed yet so will continue to update and adapt as needed.