desktop mic stand with boom 3d models

In this set, I've made a bracket adapter for my mic (since the included one wouldnt work for my desktop mic, cable management brackets, and a table base that is fixed to the bottom of any ikea table with a stubby coarse threaded screw (benchy for...

My church has two broken mic stand swivels, but I couldn't find a replacement part to order and it just seems wasteful to order new mic stands. So I got my calibers out and started measuring. After a few hours in OpenSCAD I was able to model a...

Hinge I made for a floor standing microphone arm with a 3/18 - 16 thread The threads were made possible by Dan Kirshner and his "threads.scad" (included here for ease of use) The 'thread test' stil file is just the threads part and is has the threads...

Desktop Mic stand with threads. I used my current mic threads to work the threads open a little after printing. Try not to cross thread them I printed in PLA with 30% infill and 4 perimeter layers. ... I printed the feet out of TPU

Need a mic stand for your desktop?  How about to go on the floor in front of your guitar amp?  What about that kick drum you've been wanting to capture?  The CollectorCNC Mic Stand is the answer.  It comes with a base and three different threaded rod...

This is a replacement, low-profile mic stand for a desktop. The microphone shown is from Fifine and uses the standard microphone attachment points. I have also attached a model of the neck alone if you want to use another base. ... I printed this model...

A very simple desktop microphone stand.

A very simple desktop microphone stand.

2 Part mic stand for those that do not have the space for full arm.

The top mount fits one of those inexpensive articulating mic stand (or pixar style lamps) and then slides between the desk and the wall, an interlocking cleat snaps up in from underneath to hold it in place. NOTE: this is for a desk with a 35mm...

I designed this simple desktop microphone stand in tinkercad. The stand works well and seems to be holding up quite well. The dowel I used to connect the two printed pieces is 7/8 inches in diameter. I designed the top part so that a 3/8 bolt can fit...

I designed this mic stand for my Aokeo AK-60. I wanted something with a low profile, modern, and minimalistic, but able to support most USB Microphones you throw at it. I personally use it for most video conferences, and for sound recording at my...

A stylish mic stand with a spider-like shockmount I designed a couple of years ago. I use it with Shure Beta 58A, however it should fit most similar microphones. Print three parts separately, then join outer ring with leg using M4 bolt & nut (or...

A really simple desktop microphone stand! Screw it on and you're ready to go. ...Uses a standard 3/8ths inch thread.

I re-purposed an old lapel mic I had laying around for use as a gaming microphone for my computer. the clip got misplaced so it was pretty useless as a lapel mic. Makes an awesome gaming mic though :) You'll need one M5x25 screw and 5mm nut for the...

Holds a condenser mic atop a desk Does not thread in, my shock mounts threading is too fine for my printer to replicate Hope you like it

Short, under-screen replacement Microphone stand for fifine microphone.

Instructions Build the main body and either the desktop stand, mic stand plug, or both. Snap the desired part onto the back of the main body. ...The OpenSCAD file is paramatric: you can define the width and height of the main body (in inches!) and the...

This is a Desktop Mic Stand made specifically for my MXL USB Mic. Feel free to remix this file to fit your needs to make it fit your own mic. .step file is included in the download. Print Settings Printer: RepRapGuru Prusa...

Simple pipe end plug to mount a microphone boom on the top of a dual monitor stand. It should work will all tubes that are 1 3/8 in diameter and nearly all table clamp boom arms on Amazon. You will need to deburr the tube before pushing this in. A...

This stand will hold 3 outside micrometers (0-1", 1-2", 2-3") and a caliper with a maximum jaw length of 83mm (3.25"). No supports, easily printable. 10% infill and 2mm walls. This was designed for Insize micrometers. other brands may not fit...

I lost the native mount of my pantograph during disassembly and had to print my own. ...I like that even better. The print is left unfilled for maximum durability. Link to my pantograph: https://afil.link/MAONO-Boom-Arm

Rough Draft Design of Desktop Mic Stand. Casually working on a mic stand for my desktop. The current design uploaded still needs material selection, fabrication instructions, and assembly instructions. ...Uploaded for portfolio and file keeping...

Just a simple mic stand for my Audio-Technica ATM11, that should also fit other similarly sized mics. ...I plan to update this with an adapter for the popular Shure SM57 mics at some point

I recently rearranged my desktop situation which prevents me from being able to use the mic arm that came with my mic. A few minutes in Solidworks and an overnight print later and I have this. I offset the mount a little to the fore to try to keep...

A mic holder that attaches to a standard 20mm mic stand, most acoustic instrument and vocalist set up, do both with 1 stand! ... fits well with mid tom drums along with a bass drum mic holder I have on here as well,

Its a desktop mic, used for wireless system, prepared in Auto CAD.

The original thumb nuts on my boom mic stand were not right and would never tighten, so I made ones that would. ... **Print with the skinny side down!**

boom mic cap for pilot helmet

The stand of the duck broke, to this day it hangs on the MIC BOOM, and it kept falling off of it because of the rubber stand, after it broke I decided not to give up the duck