dewalt cordless tool holder 3d models
416118 3d models found related to dewalt cordless tool holder.thingiverse
I created this to help organize and store my DeWALT cordless tools. It slides in place where the battery would go so it should work for all DeWALT 20V tools. (Maybe 12V I don't own any to try but they often use the same charger, so maybe.) The item...
thingiverse
Some DeWALT tools have a belt clip that can be attached, this adds an extra nut which the original design would hit. Version 2 has a couple of notches so the holder can slide past the nuts. The original design still works fine for tools without...
thingiverse
This is a slip on tool holder for Hart 20V cordless tools. I also created a battery holder for the same line if you look at my profile. ... The item prints best for me standing up.
thingiverse
Cutout jig for DeWalt cordless rotary tool: Place your level on the flat platform to the side and follow the edges for a perfect low-voltage ring cutout. The tube alongside the level platform can accommodate a 1/4" bolt so that the magnets on your...
thingiverse
... in 3d cad so thought this would be an easy one to start with. ...I liked the original design, but felt it was a bit loose on my dewalt tool socket so i made a few changes im happy with it. ...It printed well and in a little over an hour in PETG
thingiverse
Created this design to screw into any position and hold the 20v line of Dewalt tools. There were a couple other versions like this on here but I didn't like their design for printing as well as their overall fit onto the tool. I created this...
thingiverse
I created this thing because I need to connect my DeWALT 20V cordless vacuum (pictured) with my DeWALT 20V orbital sander. It may fit other tools and vacuums. I haven't tested it with anything else. This was the combination I needed so if anyone...
cults3d
a mountable holder for batterys/drills and other small dewalt tools
thingiverse
Tool to use with a DeWalt cordless grinder (DCG414 in my case). The grinder comes with an Allen Key to open the clamp, which I find a little light on. This tool uses 2 x 6mm Allen Key bits to engage the grinder clamp and get better purchase. ... You...
prusaprinters
A roof-mounted tool holder for Bosch Professional cordless tools using 18v battery systems.It Fits Jigsaw, Screwdriver, and Angle-grinder.
thingiverse
A hanger for the DeWalt DCF680 featuring: - trigger cutout allowing storage in both straight and angled grip configurations - storage for spare battery - fits with or without protective cap - storage for DeWalt tough case - keeps your bits at hand -...
cults3d
[Companion battery holder is here: https://cults3d.com/en/3d-model/tool/dewalt-20v-6-v-max-battery-holder-bracker {yes, the URL looks messed up, but that's correct. It saved the one I typoed and won't change it even after the model title was...
thingiverse
This holder fits Hart 20V cordless tool batteries. I have had the best success printing it standing up. ...I'll be working on a Hart 20V tool holder next so be on the look out for that if you are in the Hart 20V tool line up.
thingiverse
This is a simple tool holder for this vacuum, it has a pass through for a thin zip tie to assist foam doublestick tape This vacuum was sold mostly at Costco stores Hoover Cruise Multi-Floor Cordless Ultra-light Vacuum, Model# BH52230
thingiverse
The standard base works most of the time, but some tools (for example, the cordless orbital sander, with its dust exhaust/vacuum attachment which extends to the rear) are not going to fit properly on the standard one, thus the ability to use spacers...
thingiverse
I recently acquired a DeWalt screwdriver (model DCF680) and didn't have a good way to store it on my tool wall. The geometry should be universal (reversible) so the tool can sit in either orientation. ...
cults3d
Hang your tools up neatly using this model, this will fit any Dewalt tool which uses 20V batteries. Keep in mind torque when hanging your tools and of course weight. ... This is an easy, compact model which can be printed on a very small base so anyone...
sketchfab
Representation of a DeWalt DC759KA Drill. ...Modelled in 3dsMax and textured in Substance You can use this model in anything you like.
thingiverse
I couln'd find a tool holder that accomodates the belt clip, so this version has a 20mm base for clearance.
thingiverse
I designed this for my Orfeld cordless stick vacuum (found on Amazon), however I'm willing to guess it will also fit other cheap-from-China stick vacuums, probably not name brand ones though. It's designed so the 2 tool tips it comes with can stay on...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=537516 Instructions Using the following options: holder_x_size = 50 holder_x_count = 1 holder_offset = 0.0 holder_angle = 0.0 holder_y_size = 51 holder_y_count = 1 strength_factor = 0.66...
thingiverse
Remixed this file for easier printing and a little more strength, this works well and is pretty tough, and has great retention. ...I used an M3x12 to secure it but you could get away with a shorter screw.