dht11 3d models
322 3d models found related to dht11.thingiverse
I purchased some DHT11 sensors from amazon and but I needed an enclosure for mounting the part. ... I didn't care much for the ones I had found, so I designed my own.
thingiverse
Simple DHT11 case for greenhouse project. The sensor snaps in onto printed posts and cover holds it down. Cover could be glued to the case body, if needed. Also the sensor cage (blue on the pictures) could be glued to PCB to avoid sensor sticking out...
thingiverse
It''s designed to hold the arduino dht11 sensor, disassembled (without original blue housing) Whit two small screw to holding it on the surface. It's was used to update a laptop cooling pad whith an arduino Nano, who depending of the temperature...
thingiverse
Simple DHT11 housing with 3mm cablehole. ...Lid snaps in place, no glue needed.
thingiverse
Just a mock for DHT11 temperature and humidity sensor module in real size.
thingiverse
Case for DHT11 with lid, sensor isn't that reliable not recommend for projects that require accuracy.
prusaprinters
Simple DHT11/22 holder (stand). Print instructionsDefault settings will do.
thingiverse
A simple screw-to-the-wall type mount for a DHT11 temperature/humidity sensor. ...Compatible with screws with a 1/4" head.
thingiverse
This is a frame for the Schneider Asfora switch with a cavity for a DHT11 temp/humidity sensor. ...Print it with the flat side facing upwards.
thingiverse
besoin d'un DHT11 et d'un DHT22 pour faire une boite, du coup je l'ai mise dans un module .scad....
thingiverse
This is a box to mount a DHT11 Temperature & Humidity sensor breakout. It has a hole to mount the box to something. There is a spot for an M3 bolt and nut to hold the dht11 in place. ... Added a version with a protective roof to keep rain out and...
prusaprinters
DHT11 Sensor Case for AZ-Delivery DHT11Optional bottom piece with mounting hole included.The two pieces are meant to be clued together.I'm currently working on snap-together pieces. ...Feel free to remix.</p><p>Tolerances for the top piece are with...
thingiverse
A small enclosure to stand in the room to hold a 16x2 LCD a DHT11 and WEMOS D1 Mini in it. ...The right for size for a IOT infoscreen.
thingiverse
This is a small housing I designed for the DHT11 to be used in reptile enclosures or anywhere there may be mist or moisture that lands on the DHT11. It's designed to be open to ambient air underneath but be close at the top and sides. the wires come...
thingiverse
I made a small box that fits a ESP8266 module from WEMOS and a DHT11 sensor. ...Can still be reset with a paperclip, and can be easily plugged in.
thingiverse
DHT11 sensor isolated to separate chamber in the enclosure to minimize heat dissipation from the ESP module affecting measurements (sealant could be added for additional isolation) No screws needed Cover is held in place by sliding from the side...
cults3d
DHT11 Mount / Holder I bought some DHT11 modules from amazon that were a bit longer than the ones I could find holders for so made my own. The STL has two parts, a top and a bottom. The bottom could be left out if you didnt mount the unit to...
thingiverse
DHT11 Mount / Holder I bought some DHT11 modules from amazon that were a bit longer than the ones I could find holders for so made my own. The STL has two parts, a top and a bottom. The bottom could be left out if you didnt mount the unit to...
thingiverse
These [components](http://www.iot123.com.au/MT_D1M_DHT11), a SOCKET JIG for soldering, and 2 off 8 pin 10mm Long Needle Female Pin Header Strip are required for this build. ... ...