dht22 3d models

SDS011 Dust Monitor Syncs with DHT22 and WeMos Board for Real-Time Air Quality Analysis Version 2.0

ABS Greg. ...0.2mm. 105/245 C.http://www.blynk.io/Thermometer DHT22 mini ShieldESP8266 WeMos D1 Mini WIFIDouble Socket Dual Base Shield for D1 Mini NodeMCU ESP8266

Here is a small DHT22/AM2302 sensor holder to place it on a electric box with 20mm holes. ... Now with a version 2 who stabilizes the sensor.

This is a simple box for housing an ESP32 devkit v1 and DHT22 (temperature/humidity), BH1750 (lux) and LD2410 (presence) sensors.The box is oversized to keep the DHT22 the heat generated by the ESP32 and the LD2410 away from the DHT22.You will need 3...

The scenario involves integrating ESP32, DHT22, and MQ-135 into the same housing unit, but this setup poses challenges due to the MQ-135's tendency to overheat, potentially damaging the DHT22 sensor on the opposite side of the case. To assess the...

E,g, https://www.hackster.io/fattahalf/iot-connecting-and-interfacing-a-dht-11-with-wemos-d1-mini-feb843 https://www.instructables.com/Send-Temperature-Humidity-to-Blynk-App-Wemos-D1-Mi/ Just don't forget the 10k pull-up on the DHT22, unless you use...

This model is a remix of the model from user cncartist. ...It is a version of the housing for DHT22 sensors with an additional lock for M6 screws for mounting in a server rack.

A simple case to contain ESP8266(nodemcu v3) a DHT22 and an OLED Display 0.96intch. NOTE: Print the "Top" upside-down. ... this is a remix of https://www.thingiverse.com/thing:3340778

... side of the wall. The photos showcase the initial version without the DHT22 sensor, with stl files available upon request - though the sensor is not strictly necessary. ...Additionally, you can see the printed version made from wood filament.

I designed this DHT22 Complete PCB housing snap enclosure as Thingiverse is having mainly the DHT11 smaller type and some DHT22 enclosure with exposed DIL pin. This is a Light and quick print. Only uses 1.89meter of filament and print <55min. I...

... cap (that houses gy-302 (lux) + sht3x (temp/hum). ...I ran out of sht3x chips, so i adjusted the layout to accommodate the use of DHT22. It's a tight fit. ...Additionally, i made a split at the top of the case to make wiring the motion sensor easier.

... blynk.io. Check out the Thermometer DHT22 mini Shield at ali.pub/36ne9g. Get your ESP8266 WeMos D1 Mini WIFI board at ali.pub/36ne04. ...And don't forget the Double Socket Dual Base Shield for D1 Mini NodeMCU ESP8266, available at ali.pub/36nehf.

I needed CO2 sensors in various rooms around the house, so I came up with a custom housing for the ESP32 that includes pods for both the DHT22 temperature/humidity and MH-Z19 CO2 sensors. I flashed the ESP32 with EasyESP software and connected the...

To enhance my home environmental sensing project, I required a solution to securely attach a DHT22 temperature/humidity sensor to the vanes within an HRV ventilation system. I resolved this by designing and printing a clip that can be rendered in...

The NodeMCU's heat output consistently distorted readings from the DHT22 when both components were housed within the same enclosure. Simply switching the NoteMCU into power-saving mode did not resolve this problem. To rectify this issue, my design...

This is a ventilated mounting bracket for a DHT22 Temperature+Humidity sensor, with an integrated connector that the DHT22 plugs into. It uses standard JST-XH 2.5mm crimp pins. You can find these at about any electronics supply house. Note: You will...

This is a ventilated mounting bracket designed specifically for a DHT22 Temperature+Humidity sensor, featuring an integrated connector where the DHT22 directly plugs into. The standard JST-XH 2.5mm crimp pins used in this design can be easily...

This is the last box you will ever search for to house your Node-MCU and a DHT22 / AM2301 sensor. This box is designed on the thicker side to ensure things are safe inside. The sensor can be press-fit into the top lid hole for a nice snug fit, this...

Improved version of ESP8266 NodeMcu v2 (1.0) DHT22 Case with enhanced temperature accuracy. The upgraded design features a significantly reduced error margin, now just about 1 degree Celsius at 20 degrees Celsius compared to the original's 7-degree...

A compact and secure housing solution for a Matrix Orbital GTT35A display, an Arduino Nano microcontroller, and a DHT22 temperature and humidity sensor. This project enables real-time data logging of temperature and humidity levels with the...

[Buy Wemos with OLED](https://www.banggood.com/Wemos-Nodemcu-Wifi-For-Arduino-And-NodeMCU-ESP8266-0_96-Inch-OLED-Board-p-1154759.html?cur_warehouse=CN&p=X314102609367201509L&custlinkid=113882) * Nova SDS011 The main sensor used to measure PM2.5 and...

I loved danbaker's DHT22 mounting bracket - what a brilliant idea to integrate the connectors seamlessly into the design (although I had to order an extra set of connector pins and invest in a crimp tool). However, the design didn't quite translate...

The plan involves fitting the NodeMCU board, DHT22 temperature and humidity sensor, and photoresistor into the enclosure. Powering up the system will enable MQTT push to DataAvenue's orange API for building-specific queries. Note that there's text...

This is a versatile wall mount enclosure specifically designed for an ESP8266 NodeMCU, complete with a built-in 1x DHT22 temperature/humidity sensor module. The case consists of two distinct parts: a lower base that features four screw options for...

ESP8266: https://www.aliexpress.com/item/D1-mini-V2-Mini-NodeMcu-4M-bytes-Lua-WIFI-Internet-of-Things-development-board-based-ESP8266/32706031465.html?spm=a2g0s.9042311.0.0.iTgoyR DHT-22:...

// You must use Deep_sleep (1minute or more) mode to prevent sensor self heating from Wemos D1 ESP8266...

This is a simple mount that can be attached to one of the extruded profiles on the Prusa MINI+ (and possibly other extruded profiles that match its dimensions).It is designed to fit a DHT22 module such as the one found here:...

This is a simple mount that can be attached to one of the extruded profiles on the Prusa MINI+ (and possibly other extruded profiles that match its dimensions).It is designed to fit a DHT22 module such as the one found here:...

This is an spacer for holding the DHT22 box farther from the mounting point. will hold using M3 double sided tape applied under base to any flat surface. I needed this for better temperature- /humidity-readings in my enclosure for the printers :) ...

https://s.click.aliexpress.com/e/bvYnXKeG * One DHT22 temperature and humidity sensor is included. https://s.click.aliexpress.com/e/bzGS8PAC * An 8x8 Dot Matrix display is also required. ... https://s.click.aliexpress.com/e/wcnsHi0 Test results...