dial indicator gauge 3d models

iGaging Digital Dial Indicator Gauge

This is a bracket to mount a dial indicator gauge onto my RepRap Mendel. The bracket sits loose on the x carriage. I secured it down with a zip-tie. A future modification would be to put a slot in for a captive nut, allowing a bolt to come up...

A stand for a Dial indicator/ Gauge. The dial indicator is attached to the stand. This allows for extremely accurate measurements to be taken between the nozzle and the bed. This is an extremely effective and accurate way to level your bed. ...

... a nice tight fit so I choose not to use them. Dail gauge indicator link; http://www.ebay.com/itm/Dial-Indicator-Gauge-0-10mm-Meter-Precise-0-01-Resolution-Concentricity-Test-ED/132014888576?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

Hi, I made this holder because when I downloaded a holder from here (thingiverse) the height of the mounting plates where too high for my dial indicator gauge. So, if the distance between the end of the tip of your gauge and the hole behind the...

Original source for gauge holder: https://www.thingiverse.com/thing:1585139 .01mm accuracy dial indicator gauge from Banggood:...

Original source for gauge holder: https://www.thingiverse.com/thing:1585139 .01mm accuracy dial indicator gauge from Banggood:...

Calibrate Z and hot bed. ...For installation you need: Plastic part published 1 bolts allen M4 x 20 or 25 mm 1 nuts M4 1 bolts allen M3 x 10 or 15 mm mm 1 nuts M4 1 Dial indicator Gauge 8 mm diameter shaft

The bracket will mount the dial indicator to the hot end enclosure so exact measurements can be taken to be sure the bed is level in all four corners. It comes with a .pdf instruction manual for printing, assembling and using the gauge to obtain a...

This was inspired by several different gauge indicator dial mounts for other printers. Should be simple enough. I used the digital dial indicator from harbor freight. About $30 in store. ... Hit me up with any questions or concerns.

I tried a lot of other holders, but none was fitting my needs ;) *edit* I forgot to mention: Magnets are 6mm neodym magnets The dial gauge needs the alternative back plate with the holder thingi to fit inside my holder. ...I will add a photo soon ;)

... is alternative setup for checking depths of grooves or slots that are normally checked with depth micrometers. ...The thing is has two .201 size holes toward the top for 1/4 20 tap to make threads for set screws to hold the dial indicator in position.

Holds the dial gauge (dial indicator) directly on the x axis carriage instead of over the wobbly fan housing. Less of a remix, more of an inspiration. Compatible with http://www.thingiverse.com/thing:3417079. Other probably too. ## Why The...

Made a dial indicator mount for the Petsfang for Ender 3. My mounting diameter is 8mm, if you need a bigger or smaller diameter just send me a mail. Print it with high infill for better stability. You will need two M3x16 and two M3 nuts. ...

These are covers to protect spindles of 1" and 2" travel dial indicators while they're in storage. They fit over the most common 3/8" (9.525mm) diameter stems. I printed them laying on the side: I feel they'll be much stronger this way. Although...

... looked for a mount for the DTI that I had. I couldn't find one that matched my gauge so I designed my own. Needs a couple of M3 bolts to bolt it on where a BL-Touch would be mounted. Don't use autohome with the gauge attached because it will crash.

https://voron.dozuki.com/Guide/possible+misalignment+of+rails+causing+apparent+twist./67 https://voron.dozuki.com/Guide/High+on+One+Side+and+Low+on+the+Other+(Twisted+X+Extrusion)/45 Für Messuhr mit Öse hinten bzw 8mm Stiftaufnahme: Ich...

10mm longer version. ... Original version does not fit my petsfang

The other dial gauge indicator don't work or can't mount the dial gauge indicator properly so I spliced two dial indicator mounts together to make this one. This works well as I currently am using it now for myself, to level my bed or to double check...

Dial Gauge:...

This is a very simple dial indicator stand for the use of mounting an analoge or digital dial indicator to either measure your Z Axis endstop, or a thickness gauge (flip upside down) and even used to measure the amount of flex in a piece of material...

Wanted a dial holder that centred the dial in roughly the same line as the nozzle, and needed to put a notch in the mount so it avoided the screwheads on the X belt pulley. ... This is for 8mm diameter dial gauges

... end cooling fan for testing. Make sur that your printer is install in a very stable place. The dial indicator used is like in the picture. *** This mount doesn't work with the digital model. *** The dial indicator could be found on Amazon. ...

This is a REMIX from the amazing "Ender 3 X Gantry Dial Gauge Indicator Mount" from this YouTube video:  I just modified the original to be flat so it can work on printers that have flat surfaces like my Anycubic Kobra (standard) and my...

I took inspiration from v_rod_fer's version and made it from scratch, since his STL is way too big and I needed a different diameter (8 mm) for the dial indicator. I adapted it for the new base file (BB_Stk.Base.E3v2.E4.E3_3.11.21.stl) from...

I took inspiration from v_rod_fer's version and made it from scratch, since his STL is way too big and I needed a different diameter (8 mm) for the dial indicator.I adapted it for the new base file (BB_Stk.Base.E3v2.E4.E3_3.11.21.stl) from...

Dial indicator adjustable thickness gauge, u need to tap two M8 holes and M8 screws you want (I made my own with a hacksaw and M8 threaded rod). And share ur makes please;) ps: its really accurate for hobby standards. ...The Piece of paper is...

This thing is for using a depth gauge like a dial indictor. It uses a rubber band to keep the gauge at 0mm (or inches). ... It is based on gercole's Ender 3 Depth Grauge design https://www.thingiverse.com/thing:3732166/files I have added a...

Dial Gauge Indicator holder for a standard 40mm fan. I really liked the original dial indicator design by [@hoegge](https://www.thingiverse.com/thing:2472854) but as my CR-10 has been converted to the wonderful petfang from...

I've added a bracket for the dial gauge indicator to the hotend led mount. You will need to replace the back plate of your dial with the flat one. ... Back plate for the dial and spacers for the fan mount have been added to the files for convenience,...