diamond hotend anet a8 3d models

Here's the Cabelholder for the Anet Evolution / Anet A8. The Screw M5 14mm and Nut M5 come from my Things collection. If you encounter any issues or have suggestions for improvement on this design, let me know. ...My things are intended to be free for...

The Creality CR-10 has a higher resolution than the Anet A8, with a maximum resolution of 50 microns compared to the A8's 100 microns. This means that the CR-10 can produce prints with more detail and precision. In terms of print speed, both...

Required screws 2x M3 x30mm for the hotend, 4x M3 x20mm for the fan and the strap.

After struggling with blown fans when probing the hotend with knives and screwdrivers due to clogs and over-tightening, I've devised a fan protector. To prevent accidental pokes, the vents are deliberately narrow. ...Therefore, I made the cover 10mm...

... the mod themselves. ...The mod performs well and doesn't cause any issues with the hotend. ...Additionally, users can apply a small amount of locktite to ensure that the part remains securely attached, although it should hold its position without it.

To get it right, you'll need to use the original diamond mount part from snipermand's Witbox design. You can find that in the files section - no changes were made to his work. I want to give a huge shoutout to snipermand for creating such an amazing...

Доработки зд принтера Анет а8 плюс

The original design truly caught my eye, but one issue stood out - my diamond head utilized round heat sinks instead of hexagonal ones. To rectify this, I revamped the diamond head and heatsink mount according to my own specifications. ... In addition,...

The Creality hotend is a solid choice, outshining the Anet A8's lackluster performance. Luckily, I had an extra one on hand, so I was able to make the swap. To get it up and running, you'll need to switch to a bowden setup, but that process is...

Mounting a dual extrusion setup on your Anet A8 involves swapping out the stock hotend for a newer model like the NF-Hotend, and pairing it with the TC-01 cold end. Start by carefully removing any screws holding the original hotend in place. Then,...

BMG direct extruder with V6 Hotend or clones for the Anet A8 / AM8 or Prusa i3. X Belt Holder by kennethjiang, slightly changed https://www.thingiverse.com/thing:1666094 v6 Hotend Fan Shroud and 5015 + 40 Fang Combo by JamesK...

... at all. I used Simplify3D for slicing, so I'm unsure how Cura or other slicers will perform. Nevertheless, I decided to share this with others who might be facing the same issue. Print Settings: Printer: Anet A8 Rafts: No Supports: No Infill: 50%

https://www.thingiverse.com/thing:2972363 Re-Modeled shorter to accommodate E3D hotend modification. Uses existing holes and screws for mounting. Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: 200 Infill: 15...

- **[4]:** An Amazon link to an Anet A8 MOSFET Power Expansion Module Board, which is designed specifically for use with Anet printers but can be adapted for other models as well. 2. **Thingiverse Models:** - **[3] and [2]:** These are links to...

AM8 (Anet A8) X Carriage Upgrade for Bowden Supports two models of 3D touch sensors: one in black and one in transparent (see pictures 2 and 3) Inspired by the 3displacement project, I extend my thanks to its creator at...

... to put my entire printer on rails with the BLV mod project, I ran into a problem. ...The mount of the original X-axis carriage Anet A8 Plus was in the beta version and did not fit. ...I decided to correct this moment and design the model myself.

... to put my entire printer on rails with the BLV mod project, I ran into a problem. ...The mount of the original X-axis carriage Anet A8 Plus was in the beta version and did not fit. ...I decided to correct this moment and design the model myself.

... management header, allowing standard cable chains to fit in easily. * There's a bracket included for the stock Anet auto-level proximity sensor. ...* The existing 51mm blower will still fit, along with any guides that have already been printed.

... chain. * A bracket is provided for the stock Anet auto-level proximity sensor. * The existing 51mm blower will fit, along with any guides already printed out. ...* The FreeCAD model is included, and I wish more designers would share their models.

The original Anet A8 bearing mounting bolts are employed, while M3 nuts and bolts are utilized in all other cases. The specifications are as follows: 15mm x 12, 6mm x 4, 25mm x 4. Updates: ========= A 12mm inductive sensor mount has been added. How...

https://www.thingiverse.com/thing:2972363 Re-Modeled shorter to accommodate E3D hotend modification. Uses existing holes and screws for mounting. ...

This is a modified approach to install a Diamond hotend on an Anet A2, featuring a compacted Y-axis design.

This is a remix of this light on Thingiverse. https://www.thingiverse.com/thing:3949488 Modified it to use a adafruit 7 led jewel light. ... Edit: Updated File

Hello, avec Flow d'air optimiser. J'ai mis des colonnes à l’intérieur pour une meilleur diffusion de l'air sur la pièce. ... J'ai fait aussi un cône sur la partie rectangulaire qui va dans le ventilateur.

I really love the Black Diamond Bowden design, it's a standout in my opinion. ...To make it work with my ANET A8 printer, I made some significant changes to bring out its full potential.

This is an updated version of the Fan Black Diamond Bowden to work with the scheme from https://www.thingiverse.com/thing:2668564. It worked on my printer as shown in photos. Note: It needs support only at the nozzle, at the air outlet for the...

Bracket for securing a Diamond Hotend requires a Venturi of your choice, which most already come with 40mm holes to attach easily. This design accommodates a standard 50mm fan - identical to older style CPU fans - allowing it to fit directly above...

Couldn't find one that fit my needs and my E3D clone hotend - so here it is, a remix that will fit an Anet A8 and a 69.5mm (nozzle to top) E3D China Clone :)\nCustomized version of http://www.thingiverse.com/thing:2099577\nCreated with Customizer!

The Diamond Brass Hotend features e3D V6 heatsinks, all-metal throats, and 4mm PTFE push fittings for improved performance and durability in 3D printing applications.

Here's a mold designed specifically for silicone socks that fit the stock hotend on Anet A6 and Anet A8 printers, which comes in a 20x20x10 block size and features a standard 0.4mm nozzle. You can choose from two different sock thicknesses - either...