diet coke and mentos rocket 3d models

... Place the rocket over the opening of a Diet Coke (or other reactionary liquid) and pull the pin to release! ...Object may need to be scaled to fit snuggly enough on the soda bottle to allow pressure to build, but not so snug as it won't come off.

I have seen demonstrations of the Mentos-Diet Coke (now with Coke Zero also) at the Maker Faire in San Mateo CA and always wanted to try it out. http://www.youtube.com/watch?v=hKoB0MHVBvM . Eepbird's early work. This is the video with the cannon...

Mentos and Coke Rocket, load the mentos into the lid and slide a paperclip into the hole to hold them in place. put the bung in the bottom and fill the base with coke.  Twist the lid in place and pull out the paperclip then run... ... Ive had limited...

... strings. Partially straighten a paperclip, leaving a loop. Tie a long string onto the loop. Drop in your Mentos, stick in the paperclip, and screw it onto the Diet Coke bottle. ... Step back (if you want to stay dry), and pull the paperclip out!

●Use the parts below magnet(磁石) Φ6mm x 3mm x1 O ring(Oリング) aboutΦ22mm *See photo(写真参照) plastic wrap(サランラップ) Suitable magnet for hold(適当な磁石) mentos(メントス) x3 coke(コーラ) x1 ●Assemble in the order below 1. Glue the magnet to the holder-pats ...

... a mentos launcher. ... Instructions 1.) Print the base and the tip 2.) Place part on a pop bottle 3.) Place paperclip inside the small hole 4.) Load Mentos 5.) Screw the tip on 6.) Pull the paperclip Here it is in action: http://youtu.be/3jBHJukNEYw

Uses a tooth pick instead of a paper clip, found that unless the clip was super strait the kids could pull over the coke (not fun, but funny). A tooth pick works a bit better. Also cleaned up the inside so there is no overhang, prints just a bit...

Uses a tooth pick instead of a paper clip, found that unless the clip was super strait the kids could pull over the coke (not fun, but funny). A tooth pick works a bit better. Also cleaned up the inside so there is no overhang, prints just a bit...

[>>>] Generating Attributions log: [0] Thing Title : Mentos-Diet Coke Spray Head [0] Thing URL : http://www.thingiverse.com/thing:100563 [0] Thing Author : Weldingrod1 [0] Thing Licence : Creative Commons - Attribution [1] Thing Title : Venus de Milo...

This is a Mentos Geyser of attachment.

I was asked by a family member to make a Mentos/Coke bottle launcher nozzle thing. BUT they also wanted it to simulate a Minecraft TNT explosion. ... https://www.youtube.com/watch?v=Ig-wiTRGDPc It uses a 3mm allen wrench as a launch key I was surprised...

instructions 1. ...put pin in hole 2. fill with mentos 3. run tripwire 4. ...wait

A 2d diet coke can I designed to tease my friend who constantly drinks the stuff with.

This is a 3D printable model of a Diet Coke can with a hole cut into the top of it for pencils to go inside. This model was printed at 100% scale, and then painted afterward. ...This model is not compatible with Multi-Material 3D printing, but I can...

This is my Cola-Mentos powered Mini-Rocket. ...It there are two peaces which are connected by a threat. Just put the coke inside the Rocket, screw the Parts together and throw the mentos into the can. Have Fun! ...:-)

The version of the Diet Coke logo at Star Wars: Galaxy's Edge. The first version is the logo seen on the bottles sold in the land. ...The second version is seen on the soda fountain in Ronto Roasters.

launch - drink or dump a small amount of the diet coke so that the cap can be placed without the mentos touching the liquid. screw cap on then flip the bottle turning the top away from you or any bystander and drop/ press forcefully down on the...

I do not own any rights, all rights reserved to the coca-cola company and Disney.

I wanted to design a mentos rocket that when you drop the mentos in then it takes off! ZOOM! Print in PLA or ABS should be fine. Make sure to put supports on the base, but not in the tubes because you want those clear and clean. The diameter...

Made a slightly longer version that can hold 10 mentos. Here's a video I made featuring the nozzle. ...https://www.youtube.com/watch?v=swTocjsbRq4

No description provided.

... Space Spider 3D scanner. ...Total time to scan: 60 seconds Total time to process to watertight .OBJ with color: about 10 minutes See version 2 here: https://sketchfab.com/3d-models/diet-coke-can-version-2-color-3d-scan-9499783bed2d44b99112ec18cb5259d4

rink Coca Cola diet Aluminum Can with waterdrops and water splash end is a high quality model to add more details and realism to your projects. Detailed enough for close-up renders. Comes with detailed textures(2048x2048). Originally modelled in 3ds...

Mentos mints

... an “orange peel” effect. Total time to scan: 60 seconds. Total time to process to watertight .OBJ with color: about 15 minutes. Compare to version 1 here: https://sketchfab.com/3d-models/diet-coke-can-color-3d-scan-bbbb22f40d6a49148db682ff9f2da9fe

Drink Coca Cola diet Aluminum Can with waterdrops and water splash end is a high quality model to add more details and realism to your projects. Detailed enough for close-up renders. Comes with detailed textures(2048x2048). Originally modelled in 3ds...

I was not happy with my previous solution so I've done a new one. ... Watch video for instructions and results: https://youtu.be/qaYVDB889ic Link to my first project: https://www.thingiverse.com/thing:2343869 Link to video: https://youtu.be/wEpjfclz-0I

Pack of Coca Cola (classic, zero and diet) cans with a PBR workflow, mainly suitable for archviz/realistic purposes, but can also be used for VR/AR projects and as a game asset.

setup is super easy, first place 8 mentos in the fountain part, second push the paper clip through the two small holes towards the threads, third screw the fountain part on the Coke bottle, fourth(optional) place the rocket on the fountain I'm around...

Just for fun, always doing and learning more