diode model

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

The model will still need supports for the area where the aluminium extrusion slots in. I have included an image to illustrate how it should look in your slicer. You will also need to mirror the file in your slicer for the second print so that you...

I used solidworks to model the parts, check for interferences, and add tolerances. Previous work with bearings helped make sure parts would move smoothly. Assenbly I fixed the stepper motor to the outer casing with M3x10 screws. The 11lobe...

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

I then saw it mention by a Popular Modeller on his Youtube channel and then over the next year the number of downloads went up enormously. So it seems like its time to make some improvements from the original Version 1. DESIGN NOTES For the V1...

Update to v9: Put the K25 spring into the model, looks like it fits fine with about 2 whole whopping inches of precompression. Rounded off the corners on the PR guide (which isn't much of a spring spacer anymore) to help the spring go smoothly. Now...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

(Rotate these angles accordingly if you rotate the model.) This way, you will have two layers of crossing extrusions in the spine folds. This makes for much stronger, long-lasting book hinges.</p><p>For<strong> print-on-print</strong> technique (used...

A .3mf file and pre-sliced .bgcode file is available along with the STL models. Also prints well on a Bambu Lab P1S.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.25 stencil_pattern_line_thickness =...

Legal notes 3D printable file and model ©2022 Bethesda Softworks LLC, a ZeniMax Media company. All Rights Reserved. This is an STL ONLY for 3D printing and not a physical product. Requires a 3D printer and knowledge of 3D printing to use STL files...

Inspection: In order to assess this model, you will need to use a vernier/micrometer to check; Wall thickness (2mm ±.1) x 4 walls Internal Space (23mm±.1) x 2 walls Overall Height (25mm ±.15) x 4 corners Internal Height (23 mm ±.15) x 2 spots If you...

Tools Hex wrench 2mm and Mmm...

Tolerences are tight on this model and will require percussive pursuasion to fit a 2020 bar Base - print with inside pointing up, support the central overhang, the Ports section print as bridged ### PETG: Top- print with the inside pointing up, this...

Carbon/HEPA filter designed  for the Prusa Enclosure This started off as a modification to some of the existing designs (Bento Box, Nevermore, etc), but now I think its design is far enough away to warrant calling it an original model. The idea is to...

Infill doesn't matter because the model is a hollow shape. The filament must be elastic and reasonably heat-resistant. I have tried this in NinjaFlex which seems to work well. Anything much harder than Shore 85A is likely to be too stiff to act as a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Do a full render to see the models properly. ## Printing Print 0.16mm regular black PLA. I use a XVICO X3S - very cheap printer. ## Cassette Lid The lid is rendered the "wrong" way around. This is because it is easier to flip it on...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

You can subscribe to my youtube channel if you would like to receive a notification when it comes out.There are so much detail on the model to help hide the layer lines that I do not find it necessary to do any sanding. I did spray the frame first...

The model isn't geometrically perfect as I did the scaling in blender (The only editor I know how to use), but it works which to me is the most important thing. You will need a couple screws to put it together as the ones which come with the...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! Update 1: My Start and End G-codes in Cura working well with this firmware: ...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

Tonight, I finally decided to model the hinges in fusion and print out new ones. The test seems to work well enough. So I'm printing them with a roll of ProtoPasta Carbon FIber HTLPA. This will be my first real test of this filament. I will update...

NOTE: all models are at initial stage and not refined, nor optimized for printing, only a rough idea at the moment The unmanned colony builder/Mars MkI is a project that seeks to automate the construction of shelters and basic facilities that a...

While it worked OK for most things, there came a time when I was trying to print a model with steeply overhanging points and the stock cooling just wouldn't cut it. I designed this adapter to allow a standard 5015 radial fan (24 volt, 0.1 amp) to be...

When larger numbers of coins are required, we use 3D modeling to make a structure that supports stacking coins in 3D. The $1 money plate was designed using SketchUp, and the $2 money plate was designed using TinkerCAD. No particular reason, just to...

The redesigned Medium Mask is usable but rough around the edges as I'm still a novice at 3D modeling software. Large size mask: fits most adult men Medium size mask: roughly 85% of the Large mask; fits most adult women Materials used: 3D Printer...

Note: If you use typically use a negative Horizontal Expansion number in Cura, make sure it doesn't eliminate the in-model hole supports. If these little support towers disappear, cut back on Horizontal Expansion until they re-appear. (For example,...