dip clip 3d models

98248 3d models found related to dip clip.
Dip Clip Cup
Dip Clip Cup
thingiverse

So, the amazing dip clip by Dixon3dprinting works great for holding a Chick-fil-a cup, but my wife suggested designing an insert that would hold ketchup or another condiment. I present to you the dip-clip cup! ... Dip Clip found here :...

Dip Clip
Dip Clip
thingiverse

they work great i just started selling these. ...please download and sell around and if you feel nice enough my tip jar is open Thanks easy project to drum together

Car Dip Clip
Car Dip Clip
thingiverse

Inspired by the work of JuXas I looked at the kickstarter campaign for the original thing and saw that they can also hold round dip packages. So I tried my best to replicate that as well. The Plug should just plug in to the hole in the tray, can...

Sauce Holder / Dip Clip
Sauce Holder / Dip Clip
thingiverse

Hold all the sauce!!

vertical dip clip
vertical dip clip
thingiverse

for vertical vents

DIP-Clip for In-Circuit Programming/Analyzing ICs
DIP-Clip for In-Circuit Programming/Analyzing ICs
thingiverse

Instructions The Dip-Clips were printed from 3mm ABS filament on my DIY Prusa i3 using a 0.4mm nozzle with 0.56mm extrusion width and 0.252 layer height. ... I print on a clear mirror without Kapton tape but thoroughly cleaned with acetone and double...

DIP chip clip
DIP chip clip
thingiverse

Those clips that clip onto DIP chips are very convenient for debugging and logic analyzing. Unfortunately, they are really expensive for the hobbyist, especially when you need to buy so many different sizes. SO....make your own. Sorry, I did not use...

DIP-Clip for In-Circuit Programming (and ESP8266)
DIP-Clip for In-Circuit Programming (and ESP8266)
thingiverse

ESP-02 uses the same 2.54mm pitch, but has 7 per sides. ESP-03 and ESP-07 use a 2.0mm pitch with 8 pins per side. All these modules have different width. For ESP-12 or ESP-14 modules please use DipClipESP8266_07.stl, they have the same footprint as...

DIP IC Test Clip
DIP IC Test Clip
thingiverse

... So far, I have only printed the following versions (all other parameters left at default); | STL | ic_pin_count | ic_width | |---------------------|----------------------|--------------| |dip_clip_16.stl | 16 |8 | |dip_clip_40.stl | 40 |14 |

Dipping Sauce - Vent Clip
Dipping Sauce - Vent Clip
thingiverse

Need a handy way to dip your sauces on the road?

Dipping Sauce Vent Clip  Remix
Dipping Sauce Vent Clip Remix
thingiverse

Remix of Dipping Sauce - Vent Clip by claystarr. I found the original opening to be too large and some sauce packets could fall through. I shrank the opening by 2mm so it is a tighter fit. ... This ia a remix of item 4687502

Dipping sauce vent clip
Dipping sauce vent clip
thingiverse

This is a remix of Dixon3dprinting's design. This one has a more curved design and a slightly bigger vent opening (2.5mm). I would recommend setting the support overhang angle to about 75 degrees. ...That way the support only goes under the flat...

Dash Vent clip on dip tray
Dash Vent clip on dip tray
cults3d

chip dip tray for your car!

Sauce / Dip holder for car (Ventilation Suspender / Clip)
Sauce / Dip holder for car (Ventilation Suspender / Clip)
thingiverse

The difference between the versions is the thickness of the clip. The thin one fits better in my VW Golf, although in theory both fit. I recommend to use a pla+ filament, which can withstand warm temperatures in cars. In addition, do not turn...

IC DIP
IC DIP
grabcad

DIP IC

Dip Pen
Dip Pen
grabcad

Dip Pen

DIP switch
DIP switch
grabcad

DIP switch

Sockets DIP
Sockets DIP
grabcad

Sockets DIP

Chaves dip
Chaves dip
grabcad

Chaves dip

Diodos DIP
Diodos DIP
grabcad

Diodos DIP

DIP-4
DIP-4
grabcad

DIP-4

Dip
Dip
thingiverse

Customized version of https://www.thingiverse.com/thing:1418487 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1418487

DIP
DIP
thingiverse

Customized version of http://www.thingiverse.com/thing:374610 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=374610 Instructions Using the following options:...

DIP Switch
DIP Switch
grabcad

pcb mount DIP switch

Dip can
Dip can
thingiverse

Got bored and attempted to make a belt loop or pockey clip dip can holder. ... Made on tinker cad just couldnt get the clip right so if you can ust tag me in in

DIP Switch
DIP Switch
grabcad

DIP Swith 12 Positions, SMD

DIP Switch
DIP Switch
grabcad

DIP Swith 8 Positions, SMD

dip-switch
dip-switch
grabcad

dip key to a via

Dip bowl
Dip bowl
thingiverse

This is a simple little bowl for holding dip or salsa. ... It clips onto the side of a larger bowl, and can hang off of either the inside or outside.

DIP packages
DIP packages
grabcad

3D models of DIP packages in STEP