direct drive telescope mount 3d models

Simple telescope mount using two CSF-14 and two CSG25 harmonic drives. ...Uses Nema 23 stepper motors with encoders.A variety of gear reductions can be attained depending on the harmonic drive section.

These are simple stepper motor brackets for equatorial telescope mounts. My telescope mount is unbranded and inexpensive. I do not know if the brackets will fit other types. The brackets are for Nema 17 type stepper motors. The equatorial drive...

Lightweight telescope or camera mount. Uses two csf-11-30 harmonic drives. And two Nema 17 26:1 steppers Has a Pole Master polar alignment scope on it. ...Put on a wedge and gain a GEM or use as a ALT-AZ mount

This is a direct drive mount for the https://www.thingiverse.com/thing:4369859 fan duct. with this mount you dont have to cut away off the plastic on the satsana fan duct to be able to use it. ...

Just a model I made of the direct drive mount sold by creality. Haven't tested printing it but I don't see why it wouldn't work if you set the infill nice and high so It can't flex much. ...Original bracket is listed to work with Ender-3, Ender 3...

This was inspired by [s_gutz's direct drive extruder mount](https://www.thingiverse.com/thing:2735674), and I decided to try my own take on it. I wanted to use as many stock parts as possible and not lose any bed space. The mount also includes a...

I was wanting to mount my TriangleLab Direct Drive extruder, but I could not find a mount that I liked. AMIDE came close but she had the BLTouch mount on the left and I wanted to keep it on the right as it currently is. So, I took AMIDE’s and...

I was wanting to mount my TriangleLab Direct Drive extruder, but I could not find a mount that I liked. AMIDE came close but she had the BLTouch mount on the left and I wanted to keep it on the right as it currently is. So, I took AMIDE’s and...

This is a very simple, and well working direckt drive for bowden tubes Scad files will follow as soon as I get them cleanup a little(its a mess).

INSTALLATION: As you can see in the pictures, it mounts to the existing hotend carriage using the existing hardware. You can also use the stock extruder assembly or the one of your preference (I prefer the BantamFeeder, linked below). Again, using...

NOT COMPATIBLE WITH ENDER 3 V2 - Contact me if you want one (the fan shroud mounting is different) This version allows the full bed to be utilised - no moving the red heat sink. ... compatible with 40x20 fans with space for small buck converter which...

...... This was used to drive the precision RA axis on a home-built astrophotography mount. The 16mm bearings on each side can be pinched between a pair of pins for backlash-free mounting. For more detail please see www.td0g.ca/projects/startracker3 .

This direct drive mount uses the original Aquila bowden extruder. ...

Created a sensor mount for a direct drive microswiss creality extruder Appx -50mm x axis from nozzle.

Remix of Increased_Wheel_Clearance_Dual_Geared_Extruder_Direct_Drive_Side_Mount_for_Creality_BLTouch_Mount_Users To add a mounting hole for an M8 Pneumatic Bowden tube fitting. ...This should allow for better filament guidance into the extruder.

BI2.5 Direct drive mount Here is my design for mounting a direct drive. Tired of the oozing! so for now this will work until I can get some money for the flex-drives. Down sides: added weight & limited to 1 extruder. Up sides: NO Oozing! Much better...

you need to remove the large support but this will mount in front of a 40mm? ...fan on a direct drive extruder and allow the ability to mount a blower for a part cooler.

This is the Direct Drive mount I have created for the Ender3 and should fit the CR10 printers. ... This is for the Duel Drive mount version not the standard version.

https://www.thingiverse.com/thing:direct drive dual gear extruder Mount for ender3/pro /V2 fits Fang duct ,Bl Touch and for cable chain Fits 4010 and 4020 fans

... made and can be printed without supports, but I was unable to find a mount for my Ender 3 that I liked and that had compatibility with my bmg clone. ...And i wanted direct drive. This is a remix of.. ...https://www.thingiverse.com/thing:3419869

This is a Direct Drive mount for the Anet A2. This was not designed by me. It was designed for me by a friend JS. so please if you make this please give credit where credit is due. ... Just letting you know there might be some minor fitting you have...

I needed a direct drive mount for my ender 5 and titan extruder could find one I liked so made one. ...uses original screws and fan and covers this is version 2 added strain relief Added spacer for grater Z offset of BLTouch but mine was - without...

This is an Alternate spool holder mount for ender3 converted to Direct drive. This holder allows for the spool to be mounted right over the extruder and motor. I use this on all my ender3's along with my CR10s5. However, it should work with any...

this is a mount for the stock extruder on the ideaformer IR3 3d printer to convert it from bowden to direct drive i designed this to print be printed by the ideaformer IR3 which seems to print mirrored so if you print on a different printer you may...

Bought Chpower direct drive for my ender 3 pro off amazon. https://www.amazon.com/gp/product/B08V8MSWZM/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&th=1 I am not affiliated with this product in any shape or form Product arrived, no bltouch mount. ...

This is a work in progress and will be updated as I finish my build and dial in the part.No hardware direct drive extruder mount for Ender 3. This model uses the v-roller spacers and x-carriage for mounting. ...The extruder motor is spaced for use with...

This is a mount for the Drakon geared extruder, inspired by the Speed Drive mount (https://www.thingiverse.com/thing:3816051). My goal was to reduce the weight of my direct drive setup by using a smaller stepper motor in combination with a geared...

... Mount) - BMG Extruder - Dragon (HF) Hotend (or other Hotend with grove mount eg. E3D V6) - Short piece of PTFE tube - NEMA 17 pancake stepper (original stepper can also be used) Have fun with an absolutely stable and reliable direct drive setup.

This is a remix of the Speed Drive direct mount to fit the Kobra Max. Everything fits well and doesn't flex unnecessarily. This is designed to fit the stock stepper motor and extruder. I replaced with a pancake stepper to reduce weight. To...

I've printed two direct drive mounts for my LK4Pro. And even though they have been described as dedicated to LK4 PRO, both of them were not aligned properly. In my case they are about 1 mm too much to front and about 2 mm too much to the right. ...