discovery pro 3d models
74539 3d models found related to discovery pro.thingiverse
Holder for EzUHF on Discovery Pro. Enjoy! ...Print Settings Printer: CTC Bitzer / Replicator Dual Rafts: No ...
youmagine
***This in conjunction wit the Tarot Gimbal platform rods allows the TBS Discovery Pro to mount a 3 axis gimbal.With this combo you are able to get 4k video with no jello.*** No 3D Printer? ...***If you dont have a 3D printer, get it printed at-...
thingiverse
This adapter fits permanently to the TBS Discovery Pro Gimbal and is for the GoPro 4. Because it is designed to fit as tight as possible, a little bit of filing may be required. To install it, i removed the four bolts from the bottom gimbal plate and...
thingiverse
Simple FPV antenna mount for my TBS Discovery Pro: https://asciich.ch/wordpress/category/tbs-discovery-pro/
thingiverse
I want to make the Ultibot Discovery Pro Endurance fly... lets make it fly... here is a DJI naza mount that will soon fit to the origanal design by Steafn787. ...Print Settings Rafts: No ...
thingiverse
Replacement gimbal rear support arm for TBS Discovery Pro. Designed this so I can redesign it to clear the 36x36 stack to allow for taller stacks than 1 board. ...Not tested but measurements all match.
youmagine
... ...***Extended leg for the TBS Discovery Pro. Used in conjunction with the A-Mob arm extensions.*** No 3D Printer? ...***If you dont have a 3D printer, get it printed at Shapeways or- Nightrams 3D hub https://www.3dhubs.com/adelaide/hubs/nightram
thingiverse
A small adapter to install a Gitup Git2 in the TBS Discovery pro Gimbals. You need to buy a slim mini usb adapter ( gopro compatible ) The USB to Video cable is too large so impossible to install with the standard one. You just need to adapt the...
thingiverse
Platform for mounting for the pixhack inside the TBS Discovery Pro, with rubber damper ( use the ones inside the CUAV kit ) , there is space for the PPM cable and the main connexion between the bottom and top plate. ...The controller is fixed with the...
thingiverse
Dampened VTX Holder for TBS Discovery Pro. There is two trays, one for TBS Unify and TBS Boss transmitters and one for Unify Pro transmitters. It is using the Disco Pro gimbal dampeners (4 pieces). I'm using the black ones (for the looks and because...
grabcad
This is only rendering of Team-Blacksheep Pro Part from grabcad: Team-blacksheep Discovery Brushles Gimbal Tiger MT2814 FMVU-03MTM/C Point Grey Firefly MV Camera (USB) GoPro Hero 3 HD Camera with the Frame 9x4.7 Propeller
thingiverse
##TBS Discovery modifications Models for FPV mount, OSD, gimbal controllers and gimbal parts. For all models I use soldering nuts M3 4*4 https://goo.gl/ieohA6 #### TBS Discovery frame https://goo.gl/JYu2vq ####FPV TS835 FPV 5.8G 600MW 48CH (2-6S)...
thingiverse
TBS Discovery Gimbal Pro Core Edition 17.02.2017 Update: Roll Arm is 5mm longer to get the camera in the center of balance. ...Gimbal in Action: https://www.youtube.com/watch?v=yH-AVsWnDQw&feature=youtu.be Print Settings Printer Brand: ...
pinshape
My quadcopter design. The qaudcopter features: 2 axis gimbal clean all-in-one design easy to print long flight times up to 15inch props max. 25X25 mm motor mount for big motors Setup: Motors: MN4010 580KV Props: 15X5 ESC; 40 A Flight controller:...
thingiverse
Boscam AV Transmitter Holder for TBS Discovery Pro. Enjoy! ...Print Settings Printer: CTC Bitzer / Replicator Dual Rafts: ...
thingiverse
My first design for Discovery Pro. Enjoy! ...Print Settings Printer: CTC Bitzer / Replicator Dual Rafts: No ...
thingiverse
I have a scond design which moves the backside dampening outside the frame and offers more space inside for electronics...However, this design is the closest related to the original TBS Discovery Pro gimbal and should offer the best performance. ...
grabcad
render only of Team-blacksheep Discovery Pro with aerialmob arm extension. ... Part from grabcad: Team-blacksheep Discovery Brushles Gimbal brush-less motor FMVU-03MTM/C Point Grey Firefly MV Camera (USB) GoPro Hero 3 HD Camera with the Frame propeller...
thingiverse
This camera plate replaces the one provided with the TBS Discovery Pro and is designed for the Fatshark 600TVL camera. It might or might not work together with other Fatshark cameras as well. The hole is Ø15mm±0.5mm. You can order this item if you...
thingiverse
These will allow you to mount a set of HML 650 Retractable Landing Gear to your TBS Discovery or Discovery Pro. If you're running the Aerial Mob arms, I recommend that you increase the length of the landing gear "feet" to account for the larger...
youmagine
Unfortunately Lala has been unable to fill some orders for his excellent arm brace design. This is a concept for a 3D printable version with less hardware. Print in ABS (or better) for strength. If it needs changes, let me know. 30/10/16 - Added...
youmagine
Nothing overly wrong with the original TBS VTX, Its just that I dont always buy form Hong Kong. Now you too can print this if you like, the bonus however is that you can mirror this and put one on the front left arm too! ... Does not require different...
thingiverse
Here we have a clip-mount for the GoPro. Using this clip negates the need for the velcro strap to hold the GoPro in the gimbal. This is version 3. It's 'functional' but could still use some work. The GoPro should fit a bit tighter. My guess is that...
thingiverse
... Instructions Material needed: 1x Main plate 1x Roll mount 1x Pitch mount 1x GoPro mount (e.g. the one from Nathan_) 4x Vibration damper 2x 2208 Gimbal BL Motors 1x BGC (simpleBGC from BaseCam or any other) and the TBS Discovery :)
thingiverse
As requested, here I present my brand new design of the gimbal. **Now you can use it along with the TBS Core, as the backside dampening was moved to the top making space free at the bottom.** If you don't use the Core, then keep in mind that...
thingiverse
Here is an Ipad Pro stand to use in a discovery 300 tdi Use ABS or ASA, Avoid Pla that will bend because of sun heat
grabcad
Discovery based on Mikrokopter flight control. ... Building report: http://fpv-community.de/showthread.php?36427-Eigenbau-Discovery-Pro-auf-MK-Basis
thingiverse
Camera plate to take standard 26x26mm cameras. ...Using this in my TBS Discovery Pro which has 37mm standoff length (using carbon folding arms).