dishwasher drain adapter 3d models
154576 3d models found related to dishwasher drain adapter.thingiverse
After buying a new Bosch dishwasher I found that the drain plug was different from my old one. So that's it... Measured the tubes, drawed in sketchup, made and installed! ... I made it in Real-filament Bioflex.
thingiverse
After discovering water at the kitchen floor, I discovered hole in the drain hose. I cut it and bought a drain hose at hardware store. Needed something to connect them together. This is a result of my quick design. Works good so far. ... My dishwasher...
cults3d
After discovering water at the kitchen floor, I discovered hole in the drain hose. I cut it and bought a drain hose at hardware store. Needed something to connect them together. This is a result of my quick design. Works good so far. ...My dishwasher...
thingiverse
Hook for the dishwasher drain line under the sink. ... The drain line was getting the way of undersink storage.
thingiverse
Connecting two side-by-side dishwashers presented a plumbing challenge due to the single spigot available, necessitating an inventive solution - designing and 3D printing a Y-junction drain adapter. With space limited at the S-bend, this DIY approach...
thingiverse
I had just recently installed a dishwasher in my home and I designed this clip to keep the drain hose secured above the garbage disposal. ...Fits a drain hose that is 20 mm in diameter.
thingiverse
My dishwasher drain hose (with 20mm OD) keeps kinking and blocking as it runs through a hole in the adjacent kitchen cabinet to get to the outlet. ...This thing protects the hose from the tight angle through the hole in the cabinet to the sink drain...
thingiverse
This clamp was designed to lock the dishwasher hose to the sink drain to prevent future problems. The clamp secures the hose using nylon cable ties, as shown in the picture. ... I've included the STL as well as the Fusion 360 export so that you can...
thingiverse
Specifically made to fit Dux trap inlets but should work with the standard New Zealand and Australia drain spigots with an internal diameter 15mm Need an o-ring to seal, I used a 3/8" X 9/16' as that is what I had on hand. Metric equivalent should...
prusaprinters
Fits 22mm (⅞ inch) drain hoses. Print the clips on their side with 3+ walls. ...Avoid over tightening as the plastic can split.</p>
thingiverse
Edit 5-15-23: My models mistakenly had the drain chute about 4mm shorter than the design it was derived from, which works for my sink but likely not others. Posting original length (OL) versions. Recreated because I was having issues with the...
prusaprinters
Replacement impeller for a Bosch dishwasher drain pump. ...Print with TPU.</p>
cults3d
This is a early version of a drain hose outlet for the BOB mini dishwasher by Daan Tech. As it is now, it's made to perfectly fit my specific sink wich happens to be from Ikea. Therefore it probably won't fit your sink to well. At the moment I'm...
thingiverse
This is a early version of a drain hose outlet for the BOB mini dishwasher by Daan Tech. As it is now, it's made to perfectly fit my specific sink wich happens to be from Ikea. Therefore it probably won't fit your sink to well. At the moment I'm...
prusaprinters
This is a early version of a drain hose outlet for the BOB mini dishwasher by Daan Tech. As it is now, it's made to perfectly fit my specific sink wich happens to be from Ikea. Therefore it probably won't fit your sink to well.</p> <p>At the moment...
thingiverse
A simple adapter for allowing both washer and dryer to be connected to the same drain pipe..
prusaprinters
I was looking at the hardware store for a small adapter for my dishwasher to connect to a new drain tailpiece. the old one had a different dimension than the replacement. rather than fudging with an overpriced piece of hose, I went back...
thingiverse
Canne support de tuyau d'évacuation d'eau d'un lave vaisselle. ...A coller sur un tube PVC de diamètre 40mm. Dishwasher drain hose support rod. ...To stick on a 40mm diameter PVC tube.
thingiverse
A retractable dishwasher drain attachment for reducing splash. Designed for use with Danby Model DDW621WDB or similar dishwashers. Requires two 2M x 32mm screws and nuts, or some twist ties to hold the drain attachment to the top bracket. If...
cults3d
My dishwasher's drain pump had a couple screws come loose, which let the original gasket come out and deform. It looks like the only way I could get the gasket online, was with a $130 dollar kit. I took measurements of the lower filter housing of...
thingiverse
My dishwasher's drain pump had a couple screws come loose, which let the original gasket come out and deform. It looks like the only way I could get the gasket online, was with a $130 dollar kit. I took measurements of the lower filter housing of...
thingiverse
Support for SodaStream bottles to be clean up within the dishwasher.
thingiverse
This little access door in the bottom of the dishwasher broke so I got out my calipers and created a new one. ... Please use Version 2 https://www.thingiverse.com/thing:4233798
cults3d
Adapter for connecting a regular 80mm PC case fan to an universal 1.5 inch washing machine drain hose
thingiverse
;;;updated>> v4 I bought a used table it was missing the drain plug, so i 3d printed an adapter so i could put a inline hose shut off on and also attach a hose to drain the table.
prusaprinters
;;;updated>> v4I bought a used table it was missing the drain plug, so i 3d printed an adapter so i could put a inline hose shut off on and also attach a hose to drain the table.Print instructionsCategory: Parts Summary
thingiverse
This is an adapter to connect a garden hose to the drain outlet on a shopvac. ... Here is another thing that has an end cap that fits perfectly: https://www.thingiverse.com/thing:693149/#files
thingiverse
Internally there is a drain to collect the condensed water... ... Print Settings Printer: CTC Bizer Rafts: Yes ...
thingiverse
Remixed from the Bestway cap and garden hose adapter, I modeled the plug as close to what I saw on Amazon. It took about a day and a half to drain my pool. The cap does not need supports, but the inside part does. Use thicker walls or 100%...